|
|
|
#1
|
|||
|
|||
Hi Guys,
I have a '90 300se with about 200k miles on it. The rear of the car sags and is lower than the front. I've had mixed opinions on this, some have mentioned than the shocks need to be changed and others have mentioned the springs. The car looks as if it's squating in the rear when it accelerates. What should I change? |
#2
|
|||
|
|||
kevin,
Are you sure that the accumulators are not leaking. If they are not leaking, it could be the link from the sway bar to the level control valve. Good luck, ------------------ Larry Bible '84 Euro 240D, 516K miles '88 300E 5 Speed '81 300D Daughter's Car Over 800,000 miles in Mercedes automobiles |
#3
|
|||
|
|||
Hi Larry,
How do I find out if the Accumulator is leaking? I don't get any liquid on my garage floor every morning after the car's spent the night. Have yet to check the link between the sway bar to the level control valve. Could it be the springs or shocks? |
#4
|
|||
|
|||
kevin,
Shocks should not have anything to do with ride height. Springs of course can sag, but it is unlikely that they would sag as bad as you describe. I have made the assumption that this car has a ride leveling system. My experience is with the 300TD station wagon, and I understand that the other systems are the same type system. The most likely thing to find is the link slipping on the rear sway bar. I have seen posts that the suggest that the only other real problem can be the accumulators deteriorated. I think that if you do not find the link misadjusted, it would be time to get the manual on the system. The CD from Mercedes Shop is probably the best way to get the manual. Good luck, Larry ------------------ Larry Bible '84 Euro 240D, 516K miles '88 300E 5 Speed '81 300D Daughter's Car Over 800,000 miles in Mercedes automobiles |
#5
|
|||
|
|||
Here is a posting from Listers that explains what might be causing the sagging:
********************************************* Date: Fri, 28 Apr 2000 11:48:59 -0500 From: Stuart Steele <ssteele@switchsolutions.com> Subject: RE: [MB] 126 rear shock & spring R&R DIY'er? Hello, Christopher and List: Alas, I have nothing of my own to offer, except that I know where to look! - Stu Ritter has provided just about all that a person can know about this subject in a few pithy posts, which I have copied below. Stuart Steele Christopher Wright asks: > > Rear end is sagging a bit. Is this a pretty good DIY'er? >> here we follow with Stu Ritter's posts on the subject << Stu Ritter writes on 2/14/1998 10:03:00 AM, in a message entitled "[MB] Sagging in the rear 126 chassis": On the 126 chassis, the first place to look when the rear end is sagging is the differential mount. The mount collapses internally and is very hard to see. Most MB mechanics don't recognise this problem. The entire rear subframe is mounted at three points. The two forward big rubber mounts and the mount at the rear of the differential. When the differential mount collapses it changes the rear ride height and the rear end sags. It is a very rare case when springs sag on a Benz. It is almost always the mounts (lone exception, my father-in-law's 300SE, of cource). I think I have replaced two sets of rear springs in 27 years and hundreds of rear differential mounts. Gas shock absorbers do not control or maintain ride height. The purpose of the gas in the shock is to prevent the oil from foaming when it gets hot under hard usage. You can compress the shock with about 70 pounds of push. That doesn't go very far in holding up a 1500 pound corner on a 3700 pound car. Considering you have an 83 126 chassis, if the rear mounts have not been done yet, I would replace both the rear subframe mounts and the differential mount. You will be amazed at how the car will feel when this is done. It will feel very new. As the rear rubber mounts collapse, over time, they allow the rear wheels to start steering the car. It makes the car seem a little nervous and darty. With new rubber mounts the car just settles down and becomes very relaxing to drive.. Stu Stu Ritter writes on 4/9/1998 12:17:00 PM, in a message entitled "Re: [MB] [MB Digest]rear spring seats": > Stu, my car, rear height, is too low. I measured the height at the spring. Did you measure the spring height before it was installed and compare it with the height of the spring that was removed. Did you do the spring replacement yourself?? When we did replace a set of rear springs, we compared the uncompressed height of the spring from the car with the new one and were surprised that the new one was about .5 inch lower. We then put the springs on a scale and measured the distance compressed for a given force and the taller, used springs moved three times as far under the same weight as the new springs. We were sure the old ones were collapsed and we were correct. >>From the lower edge of the upper steel cup, down to the upper surface of the >trailing arm and parallel to the spring, I get 7.5 inches. Both sides. Another >'81 300 SD measured 8.25 inches. One would conclude that the springs are too >short. These are new, OE springs. My experience has been, on the whole, that: when the rear of the car is sagging, both the rear subframe mounts and the differential mount have collapsed into themselves and have altered the ride height. I have only replaced one set of springs on a 126 chassis in the past 18 years and have replaced innumerable subframe and differential mounts. 107's and 126's seem to show the degeneration of the sub- frame mounts the most by sagging quite a bit. New mounts and they just pop right back into place. > The only parts I have not changed are the subframe mounts, left and right. >They look good. Flexible and the rubber is black and glossy. > I guess I could put a thicker seat in, if available. That is like changing >the springs out all over again, though. > > Any thoughts? > Much appreciated. > > Rick Hesek as above...the rear mounts.. Stu Stu Ritter writes on 1/13/1999 7:40:00 AM, in a message entitled "[MB] How low is too low?": All measurements of the chassis and all height adjustments are done with the engine off. If engine torque load is causing the rear end to sag, there is a good chance that the rubber mounts for the rear subframe and the rubber mount for the differential are sagged and should be replaced. You car is 9 years old and Manilla is quite hot if I remember. I would think that the rubber mounts (which help determine rear axle position and therefore ride height) have served their time and could be replaced. This will probably help.. Stu Stu Ritter writes on 1/13/1999 11:50:00 AM, in a message entitled "Re: [MB] How low is too low?": >Thank you for your reply. I will check the subframe and differential rubber >mount first thing in the morning. Stu, My previous investigation shows >that there are three pieces of rubber mount stack together on the subframe, >is it okay to add one more? The rear subframe mounts are one-piece mounts. You cannot "stack" anything else in to change the ride height. That is determined by the spring height. The engine does not have enough torque to compress the springs..more than likely, the rubber is compressing and allowing the ride height change. I also forgot to mentioned that when in >Reverse, the rear will suddenly rise by couple of inches. One more thing, >ride height is okay when engine is shut off, however, when there are one or >two passengers at the back, the car's rear will sag significantly, more so >when it is on drive. Are the springs and shock absorbers due for >replacement? The shock absorbers do not affect the ride height..ever...at all.. The only way to check the spring is to remove it, compress it with a known force and measure the distance and compare that to the manual. I have known one other 300SE 1989 model year that had sagging rear springs that we replaced. Normally a Benz never needs springs.. Stu |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
300 TE (W124) rear wiper woes | rjk | Tech Help | 9 | 07-07-2008 12:42 PM |
W107 77 450sl Rear suspension sags | joelpdavis | Mercedes-Benz SL Discussion Forum | 7 | 02-06-2004 11:38 PM |
Rear Subframe Bushings | git0 | Tech Help | 5 | 11-23-2003 09:01 PM |
Problem with rear dome light switch 420SEL | William | Tech Help | 2 | 11-10-2003 03:46 AM |
92 300SE rear door & subwoofer speakers not working | ELITEkid | Tech Help | 2 | 06-29-2003 10:53 PM |