Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-05-2003, 12:51 AM
Registered User
 
Join Date: Feb 2003
Location: Niantic,Ct. Attawan
Posts: 143
Tips on removing a rear widow, 190E

A sweet little boy (?) with nothing better to do threw a rock thru my rear window.
I have access to a parts car for a window. I just need info on 2 things.
1. If I find him, can I castrate him with 2 bricks ?
2. Anything I should know about removing "good" window?
Any help would be appreciated ASAP!
Thanks in advance!
-M

Reply With Quote
  #2  
Old 09-05-2003, 09:47 AM
Registered User
 
Join Date: Oct 2002
Location: Portsmouth UK
Posts: 170
Distracting the young chap with candy - while accurately positioning the bricks could help!
__________________
NormanB
230 TE (W124) 1989 with 153,000 miles on the clock - hoping for at least another 100K
Reply With Quote
  #3  
Old 09-05-2003, 10:05 AM
Mercedes Maniac's Avatar
Member
 
Join Date: Jun 2003
Location: Colorado
Posts: 32
For castrations, I prefer the Burdizzo Emasculatome. But in a 'pinch' vice grips will do!
__________________
'87 190E 2.3-16
Heated Seats, Graphite Dash,
Delsing shift bushings
Reply With Quote
  #4  
Old 09-05-2003, 01:10 PM
Registered User
 
Join Date: Jul 2002
Location: S. Texas
Posts: 1,237
I just removed the rear window from a '72 350 slc and it went very easily. Granted the seal was old and I did not try to save it so there was no special care needed. My slc has an aluminum molding around the glass that must come out first. If yours has this then be very careful before you start ripping and tearing.

I took mine out using a wide, flat pry bar called a Wunderbar. You must pry up very gently so as not to kink the molding. It is very soft. One bar on either side and a friend to help lift it out might work.

Once my molding was out I just ran a sharp knife around the outside and cut a way the old seal. Once you get the seal cut off the outside you can see the edge of the window. Cut down along side the glass. If your car is fairly new the seal should be soft enough that the window should just lift out. REMEMBER; if you have a rear window defroster there is a power cord. Mine comes out on the bottom passenger side corner. It unplugs through the trunk. Obviously if the back glass is broken you don't need to worry about this.

A faster way is to use a piece of stainless steel wire. Push the wire through the seal, tie each end to a short piece of wood as a handle, and then pull it around the window. It will cut the seal as slick as can be.

I just had a run around with the local glass shop about putting my glass back in. They put the window in and THEN tried to install the aluminum molding into the seal. It won't work this way. The molding HAS to be installed BEFORE the glass is put into the car.

Once the molding is in place you have to wrap a 1/8 to 1/4 in. rope around the lip that holds the seal into the car body. This opens the lip so that it will slip over the frame easily. Be sure that the two ends cross over at the bottom of the window. Place the window into the frame with the bottom lip in first. If you have a rear window defroster be sure that the wire goes in the hole and that

Be sure that the window is lined up in the center of the frame, i.e., that the corners will be in the right place once the window is in. Then while you get a friend to push down gently on the botton of the glass get inside the car and start pulling out the rope. This will bring the lip of the seal out over the frame and the glass should just pop in. One of those little hooked glass installer's tools will help bring the seal lip out over the frame.

Good luck.

ps. The little hooked took is also handy for grabbing the cajonies of little kids that throw rocks.
Reply With Quote
  #5  
Old 09-05-2003, 04:09 PM
haasman's Avatar
Registered User
 
Join Date: Jun 2001
Location: San Francisco, CA
Posts: 3,097
I believe the '72 350 slc model has the non-bonded window. The 190e glass is glued into the frame. It requires a totally different process to remove successfully.

Haasman
__________________
'03 E320 Wagon-Sold
'95 E320 Wagon-Went to Ex
'93 190E 2.6-Wrecked
'91 300E-Went to Ex
'65 911 Coupe (#302580)
Reply With Quote
  #6  
Old 09-05-2003, 11:16 PM
Registered User
 
Join Date: Feb 2003
Location: Niantic,Ct. Attawan
Posts: 143
Thanks for the help help guys, Sat. is the day- will let you know how it turns out.
Good idea on the "hooked tool"
(the little bastard!)
Nice area of Mystic Ct. too!! I'm surprised! And still can't figure out my Benz, not the Volvo, or the Firebird!!??
Oh well!
Take care,
Mel
Reply With Quote
  #7  
Old 09-07-2003, 12:34 AM
Registered User
 
Join Date: Feb 2003
Location: Niantic,Ct. Attawan
Posts: 143
Window out and into my car today. SOOO simple, a little harder to install of course. Always seems quicker tearing something apart than putting it back together!
Thanks for the help!
Now if everyone here who has helped me could just buy a BMW, so I could get the same help there.........
So she's together, but running really rough-my Brother thinks fuel pump.
Still not a bad deal at $900.00. My next project was a paint job. I almost decided to keep her today. So comfy, very solid feeling!
I'm rambling. Thanks again for the help!
-M
Reply With Quote
  #8  
Old 09-04-2023, 04:26 PM
Registered User
 
Join Date: Jul 2006
Posts: 44
Rear window

Kip is correct with his instructions

Also the rear window of 190e is not bonded. At least until 1987.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 11:25 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page