Looking for tools not yet in the list
 

Does anyone near Norfolk VA have a timing chain crimping tool for a 240D to rent or sell?

chonahe@live.com

Hello
I need to rent a ball joint press for a 560 SEL or does anyone no a shop here on long island that would press them in for me

I saw that Billybob has a ball joint press for rent for a 560sel but I can not send him an email for some reason

Hi I need to change the front shocks on my 1989 300E (W124)? Can anybody rent me the coil spring compression tool - I live in DC Metgro area/MD.

Anyone have a w201/w124 ball joint press I can borrow or rent? I live in the Atlanta area! Thanks in Advance!

------------dirtyhands

Anyone have the valve spring compressor for the valve stem seals? Need it for a 420 (m116)...

I'm looking to replace all four rear subframe bushings on a '94 w124 (e420) in the near future and was wondering if anyone has the bushing R&R tools. The part numbers for these tools are

201 589 10 43 00
201 589 11 43 00

I'm not sure how necessary these are for the job, but I'd rather not spend a day sweating these guys in and and out (any experience would be appreciated!).

Thanks -- Greg

Lower Control Arm Bushings
 

Hi,

Will somebody suggest a tool to remove and install LCA Bushings on a 98 e320 (w210) I will rent or buy.

I am looking to see if someone has an internal spring compressor that I can borrow, rent, or maybe buy. I am located in Milpitas, CA. 45-min south of San Francisco.

I have a 2000 E320 Wagon

Email me at surakung@gmail.com if you do. Thanks~

(pictured below)

Valve Adjusment tools and/or compression test!
 

By any chance does any one have the tools needed for a valve adjustment and compression test? I mainly need the valve adjustment tools.

I have plenty of feed back on other sites and I only need them for one weekend. I will pay shipping both ways and maybe a small fee if needed ;)

I am new to diesels and also a senior in high school and at the moment I cant afford a set for my self, or else I would and keep them for future use!

I am in Danville, California..

Thanks very much!
Andrew
andrewtexas123@hotmail.com

I'm interested in renting the following tools.....
 

I want to replace the injector nozzles in my 617 engine and remove the prechambers soz I can replace the seal. I've been getting some leaking in those areas and I feel it's time to see what she'll feel like with new injector nozzles.

Here are the tools I'd like to rent:


34) Prechamber ring wrench, pin type, 60X, 61X....Billybob............................$15

37) Prechamber removal tool, screw press, 61X.....Billybob............................$25.

20) Injector pop tester........................................Grezer...........................$20.


If these tools are still available let me know. I'd like to handle these transactions via money orders and mail.

I have a 1982 300sd with 350k on the clock. She runs well but always needs more attention than I'm able to give her. :( I've been happy to own her for the last three years.

Thanks
Allen

IP Delivery Valve Splien Scoket 87 300D
 

Looking to rent a spline socket for the delivery value removal off the injector pump of a 1987 300D

MB part number 617 589 01 09 00

Dealer cost $58.

Looking for tools in all the wrong places ...
 

I'm looking to replace all four rear subframe bushings on a '94 w124 (e420) in the near future and was wondering if anyone has the bushing R&R tools. The part numbers for these tools are

201 589 10 43 00
201 589 11 43 00

I'm not sure how necessary these are for the job, but I'd rather not spend a day sweating these guys in and and out (any experience would be appreciated!).

Thanks -- Greg

I am doing the same job as Greg, if anyone has the tool(s), please contact me as well...

I personally dont stipulate the OEM part, the B201-1143 is prefectly fine with me...

CIS-E Fuel Pressure Tester
 

Would like to rent or possibly buy a CIS-E Fuel Pressure Tester. If anyone has one to rent I would appreciate it.

Thanks, Rebe

Email at bikerman@swbell.net

Looking for a modified flare nut wrench for oil cooler lines on a 1985 300td. It's the modified 1 and 1/16 box end wrench.

anyone have a set of valve wrenches to rent? nobody in the master thread is reachable, and i need to do the job. :(

Special tools are not needed at all for the subframe mounts. The ones in front of the wheel can be pushed out with a deep well 27mm socket and a floor jack. The rear bushings can be removed with a piece of 3/8" all threaded rod, some nuts and washers.

I'll need a front wheel hub puller, MB tool #116 589 33 00.

This is for a 1984 300 CD.

Yes, if you still need them.

I was successful using a "rental" from the local AutoZoo, so I no longer need this.

Anyone have the Sunroof for 300E tool PN 124 589 00 37 00 Assembly Pliers for preloading the sunroof Or even the dimensions of the span so I can make my own?
Rent or Buy?
I am in Long Beach, CA
Thanks
Gene
genep123@gmail.com

Rear Lower Control Arm bushing extractor
 

I need a mounting tool extractor for removing the bushing out of the wheel carrier supporting joint. The rear control arm outer bushing is pressed in and I need an extractor to get it out.

Here is a photo of the tool I need.

MB part# 202 589 00 43 00 or 202589004300

Looking for Glow Plug Hole Reamer for early larger style 240D gp holes (18mm),
I don't really want to spend $80 to buy this, anyone in Portland OR or nearby got one?
I've got a hazlet valve adjustment wrench set if you need them

Tie Rod Separator-screw type
 

Looking to rent screw type tie rod separator for 1984 300D (W123). BillyBob is listd as having one, but I can't email him 'cause he is banned.

Anyone got one they will rent?

Looking for this injector adapter to fit 3.5L OM603's. It's M22 X 1.5mm

Not available any longer from Pelican

Pelican Parts.com - Injector Adapter

Well, I just went ahead and ordered one online. As often as I deal with 3.5L's, it would be worth it. Hope they aren't out of stock!

Just got the email...

Thank you for your recent order, however the Sir Tool M-0092 has been dis-continued and is no longer available. Your credit card has not been charged.

Rats!

Looking to rent a rear main seal tool for an M104. FSM lists the part number as

601 589 03 43 00

But it looks like its been superseded by

111 589 08 43 00

Anyone have one?

Power Steering Pulley remover tool?
 

Anyone renting the tool you need to remove the pulley from the power steeting pump?

Need it for a 1984 300D.

Looking to rent a 603.97/3.5/rod bender splined prechamber locking tool.

Sixto
87 300D