|
|
|
#61
|
||||
|
||||
Quote:
Thanks.
__________________
"In wine there is wisdom, in beer there is strength, in water there is bacteria." |
#62
|
||||
|
||||
Was a little anxious to get started on metal fab. Got things set up and made the first set of panels for the firewall. These three panels are ready to trim to fit and weld in.
Using metal just a smidge thicker .041 vs .038. Will probably fit a little closer and tack in. Until the engine is placed the lower part (tunnel) might need to be modified. But at least some forward motion. The new engine and trans should be here this Wednesday, I should have by Friday. Then I can start checking everything.
__________________
"In wine there is wisdom, in beer there is strength, in water there is bacteria." |
#63
|
||||
|
||||
I just got a chance to check, imagine my surprise when it turned out to only be 6.75" of travel! It's 34.5" long in total, but center-mount (not end mount) from my 99 300M. I thought it'd be more due to where it was mounted & the tighter turning circle the car has than many other FWD R&P cars... but not that much, apparently.
You might want to consider an "Exploration" trip to the junkyard. Find a car with R&P, and then measure its travel lock-to-lock. My hunch is you'll need a center-mount because you will NOT find a R&P unit that can do end-mount that both offers only 19.5" length from output shaft end to output shaft end (not body length) AND 7+ inches of travel. The engineering to do that is just not feasible for any manufacturer unless you have maybe a manual rack custom-fabbed. Keep in mind, steering is all geometry. You'll want to keep bump steer to a minimum but still meet Ackerman geometry. You will be able to do so with a R&P unit and you may be able to decrease your turning radius if you do the geometry right. It is very likely the old pitman arm moves nowhere near the 8" you see when going from lock to lock at the tie rod ends thanks to simple trig (ok, somewhat complex, but simple if you dumb it down enough).
__________________
Current: 2021 Charger Scat Pack Widebody "Sinabee" 2018 Durango R/T Previous: 1972 280SE 4.5 2014 Jeep Grand Cherokee Limited "Hefe", 1992 Jeep Cherokee Laredo "Jeepy", 2006 Charger R/T "Hemi" 1999 Chrysler 300M - RIP @ 221k |
#64
|
|||
|
|||
Quote:
Re: center-mount vs. end-mount, is it possible that you are referring to the attachment points of the tie rods? As contrasted with the mounting points of the rack housing. Would you put up a pic or two? With some dimensions marked. |
#65
|
||||
|
||||
Quote:
The downside of such a rack is that it is inevitably longer than a more "Traditional" end-mount rack, but since it can be mounted "out of the way" it should not matter as much, I would assume. Album here
__________________
Current: 2021 Charger Scat Pack Widebody "Sinabee" 2018 Durango R/T Previous: 1972 280SE 4.5 2014 Jeep Grand Cherokee Limited "Hefe", 1992 Jeep Cherokee Laredo "Jeepy", 2006 Charger R/T "Hemi" 1999 Chrysler 300M - RIP @ 221k |
#66
|
|||
|
|||
Thanks Tom; that would appear to be a front-steer configuration (rack in front of axle). Are you able to say what the steering arm length is? (Ball joint center line to tie rod end center).
|
#67
|
||||
|
||||
I would have to measure. The strut itself is the centerline for the (top) of the steering system, I assume you're looking for the length from the strut arm to the center of the strut itself? The R&P is mounted to a crossmember in front of the firewall, and the tie rod ends connect to the steering ends of the front struts.
__________________
Current: 2021 Charger Scat Pack Widebody "Sinabee" 2018 Durango R/T Previous: 1972 280SE 4.5 2014 Jeep Grand Cherokee Limited "Hefe", 1992 Jeep Cherokee Laredo "Jeepy", 2006 Charger R/T "Hemi" 1999 Chrysler 300M - RIP @ 221k |
#68
|
|||
|
|||
Quote:
[/QUOTE]The R&P is mounted to a crossmember in front of the firewall, and the tie rod ends connect to the steering ends of the front struts.[/QUOTE] Is the rack mounted forward of the wheel spindles, or aft of the spindles? Do the steering arms point forward from the struts, or back from the struts? |
#69
|
||||
|
||||
The ultimate Intrepid (and Vision, Concord) steering fix
For anyone curious here's info and pics on how a Chrysler LH with R&P is setup. The rack is mounted pretty much on the firewall (on a "Frame" crossmember right in front of it). This is behind the front axle centerline.
__________________
Current: 2021 Charger Scat Pack Widebody "Sinabee" 2018 Durango R/T Previous: 1972 280SE 4.5 2014 Jeep Grand Cherokee Limited "Hefe", 1992 Jeep Cherokee Laredo "Jeepy", 2006 Charger R/T "Hemi" 1999 Chrysler 300M - RIP @ 221k |
#70
|
|||
|
|||
Another center tie rod mount rack is a GM J body ( 81 to 05? Chevrolet Cavalier, Pontiac Sunfire , Olds Firenza , Buick Skyhawk , Cadillac Cimarron )
|
#71
|
|||
|
|||
With respect to the Mopar R&P which Tom has identified, although it is a center take-off type, it is also a front-steer type, i.e., the steering arms at the uprights (struts, knuckles,etc.) are forward of the wheel spindle. To make a right turn, the rack also travels to the right. Given the configuration of the W114/115 crossmember, it is difficult to get the steering shaft in place to use a front-steer R&P.
A common rear-steer, center take-off R&P can be sourced from GM J-platform cars, and forms the basis for a number of after-market kits, many of them directed at early Mustangs. J-bodies include: Buick Skyhawk, Cadillac Cimarron, Chevy Cavalier, Oldsmobile Firenza, Pontiac 2000/Sunbird/Sunfire. |
#72
|
|||
|
|||
As for " Ackerman " ( toe out on turns ) , that is dictated by the angle of the steering arm relative to the wheel ( when looking from above. ) Look on the net for a drawing of steering arms / center line of the car.
When using ackerman, a front steer car will have the outer tie rod end close to the tire, a rear steer farther away from the tire. If you move the outer tie rod end closer to the spindle while keeping along the same angle, you won't change ackerman but you will reduce tie rod travel needed to complete a turn. I did this on a car bu drilling / tapering a new hole along the arm. Not sure if your arm will have enough material or not. |
#73
|
||||
|
||||
Tom, Frank, and 97,
Thanks much for your conversations today. Oahu does not have salvage yards like the mainland. I'm not sure if it's for environmental or financial (due to high real estate prices) reasons, but no acreage of salvage cars. So combing wrecked cars is not an option. For both my Jeep/Vortec and Mercedes/Vortec build I've had to buy from the mainland and ship over. Not only no availability, the largest "Salvage Yard" salesman didn't even know what a Chevy Vortec engine was. So trying to get their help looking for steering racks would certainly be futile. In the many hours I've spent so far reading forums on steering swaps it seems the most prevalent R&P is from the Chevy J-bodies. A few aftermarket companies even base swap kits on this rack. I can buy locally, rebuilt racks for under $100 from OReily. Basically this rack has 2.8 or 2.5 to 1 ratio, 6" of travel, for rear steer, and it's two mounting points are pretty close in width to match the W114 frame rails at the point of installation. This rack, as mentioned, connects to the steering arms from the center of the rack, not each end. So to keep the same W114 geometry a bar needs to be fashioned to attach to the racks center point with connection points at each end to match the existing inner tie rod bolting locations, approx 19 1/2". So a modified drag link, if I have my terminology correct. Similar idea to the pic above. I need to re-install my steering box and map out all the existing points, so when I make all the new parts and mounts I can duplicate the existing. I'm planning on buying one this week and checking to see if what I have read matches my estimations. The only downside I see at this point is going to be a reduced turning radius. This is the common complaint with the swap. And the fact that it seems that even with all the posted swaps and companies that make conversion kits, no one offers a rack with more than about 6 3/4" travel. In some swaps I've read they move the tie rod connection to the wheel closer to the spindle, as previously mentioned. I need to measure this out before I cut everything out to see how far inward I would have to go to achieve the same turning radius as stock with only 6" of travel.
__________________
"In wine there is wisdom, in beer there is strength, in water there is bacteria." |
#74
|
||||
|
||||
FYI it'll also reduce bump steer if you do mount the ends closer to the spindle. Basic leverage principles apply (the lever to push the tie rods is longer when it's further from the spindle, thus bumps more easily can mess with your steering angle). Killing two birds with one stone = good.
__________________
Current: 2021 Charger Scat Pack Widebody "Sinabee" 2018 Durango R/T Previous: 1972 280SE 4.5 2014 Jeep Grand Cherokee Limited "Hefe", 1992 Jeep Cherokee Laredo "Jeepy", 2006 Charger R/T "Hemi" 1999 Chrysler 300M - RIP @ 221k |
#75
|
|||
|
|||
The Chevy Cobalt replaced the J body so I'd have a look at one of those to see if the rack is similar.
The late 80's J body could have been had in a 1.8 and 2.0 OHC turbo so there is a small chance of a faster ratio rack. |
Bookmarks |
|
|