Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Vintage Mercedes Forum

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 10-11-2017, 11:20 PM
Registered User
 
Join Date: Dec 2016
Posts: 119
Running k-jetronic without fuel accumulator?

So after getting the fuel distributor fixed on my 78 280slc, I noticed that starting was getting more and more difficult. I soon identified the fuel accumulator as the culprit. Fuel was coming out of the vent fitting on the back of the accumulator, indicating that the membrane inside was punctured/cracked.
Trouble is: the exact part number is out of stock almost everywhere, an when it is available the price is ludicrous (over U$ 300), because this same part number is also used on a Ferrari of the same vintage. It's pretty obvious that it will be a while before I get my hands on a new one.

So my question is this: It is bad to run without a fuel accumulator? (Besides the obvious starting issues). I'm thinking that removing the accumulator could improve starting slightly, given that I would be eliminating a pressure leak at least, right?

Reply With Quote
  #2  
Old 10-11-2017, 11:32 PM
Registered User
 
Join Date: Feb 2011
Location: Modesto CA
Posts: 4,075
Bad? No. As noted, starting, particularly when hot, may be more difficult. The accumulator serves to dampen pressure fluctuations that can be caused by sudden changes in metering plunger position, or by voltage changes that result in pump speed variations.
Reply With Quote
  #3  
Old 10-12-2017, 06:13 PM
Registered User
 
Join Date: Jan 2012
Posts: 7,534
The external vent is a really , really bad design. Even worse on some other brands where the vent is atop the exhaust. I've seen other K jet cars plumb the vent into the tank to pump hose to eliminate the leakage / fire issue.

I'd look around for any accumulator with the same fittings and go from there. Unless someone has an actual pressure / volume chart from Bosch, I'd think the only real difference is a mounting bracket / fitting location.

If you bypass the accumulator, when hot manually running the fuel pump before cranking to build pressure might be helpful.
Reply With Quote
  #4  
Old 10-12-2017, 08:17 PM
Registered User
 
Join Date: Dec 2016
Posts: 119
Yeah, currently I am running the pump manually before every start. I simply disconnected the safety switch on the air sensor body so that the pump runs with the key on the ignition on position.
The vent on my accumulator actually connects back to the fuel line, just before the pump inlet.
Reply With Quote
  #5  
Old 10-13-2017, 08:20 AM
Registered User
 
Join Date: Sep 2011
Posts: 926
Quote:
Originally Posted by 97 SL320 View Post
The external vent is a really , really bad design. Even worse on some other brands where the vent is atop the exhaust. I've seen other K jet cars plumb the vent into the tank to pump hose to eliminate the leakage / fire issue.


The vent should never be external. The accumulator should only vent back to the tank, and the only time it should actually “vent” is when it is bad and the membrane has failed.

My understanding of the accumulator is NOT to dampen pressure fluctuations. Once the spring is fully compressed, it cannot do anything other than expand to increase (or balance) low pressure. Higher pressures are relieved by the fuel pressure regulator at the fuel distributor. After the fuel pump is turned off, the accumulator should help maintain pressure as small leaks (like a leaky injector or pressure regulator) allow the pressure in the system to decrease. The spring in the accumulator helps maintain pressure and keep the fuel in the lines from evaporating, which might create a vapor lock situation.

If you have no fear of vapor lock or hard hot starts, then you may be just fine without the accumulator in the system.

I believe this is the one I used on my 1978 450slc 5.0:
https://www.ebay.com/i/351736499245




Sent from my iPhone using Tapatalk
__________________
Past mb: '73 450sl, '81 280slc stick, '71 250, '72 250c, '70 250c, '79 280sl, '73 450sl, parted: '75 240d stick, '69 280s, '73 450slc, '72 450sl,
Reply With Quote
  #6  
Old 10-13-2017, 07:58 PM
Registered User
 
Join Date: Jan 2012
Posts: 7,534
Quote:
Originally Posted by fonzi View Post
The vent should never be external. The accumulator should only vent back to the tank, and the only time it should actually “vent” is when it is bad and the membrane has failed.
K jet SAAB's had an external vent, right above the transverse muffler.

I'm, pretty sure same era VW's had an external vent also.

I need to define what is being vented. With this type of accumulator, the "vent" side needs to be open to atmospheric air pressure ( or through the fuel tank ) so the diaphragm can move. If the " vent " is blocked, pressure required to move the diaphragm will be higher. There are accumulators ( in general ) that are unvented with gas pressure as a countering force. ( ABS / hydraulic suspension for example )

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 10:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page