Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Vintage Mercedes Forum

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 01-14-2004, 06:36 PM
Registered User
 
Join Date: May 2003
Posts: 7
How to fix a broken control arm pivot?

Yesterday I discovered that my '73 280 (W114) had broken its driver side lower A-arm pivot off the cross member. You can see in the attached picture that the rear part of the pivot is completly broken off and the front part is about to go.
Has anyone gone through this fix before? Can I weld the pivot back onto the cross member? Or do I need to replace the whole cross piece? It looks like I'd have to pull the engine to replace the cross member. I don't want to do that!
Is this a common failure?

MOOSE

Reply With Quote
  #2  
Old 01-14-2004, 06:38 PM
Registered User
 
Join Date: May 2003
Posts: 7
I don't know what happened to the picture. I'll try again.

MOOSE
Attached Thumbnails
How to fix a broken control arm pivot?-broken-benz-1-resized.jpg  
Reply With Quote
  #3  
Old 01-14-2004, 07:14 PM
Registered User
 
Join Date: Jan 2001
Location: Alexandria, Virginia
Posts: 5,480
I haven't seen or heard of this problem before. You might be able to weld the original contol-arm mount back together. You may need to fabricate and add reinforcements to the repair. It all depends on how good a welder/fabricator you are and if you believe you can make a reliable repair with the crossmember (also kown as a 'subframe') installed in the car. If you have any doubts, you would be better off replacing it. Wether you decide to repair or replace the subframe, it's possible to fabricate an engine support bar and chains to straddle the inner wheel housings or front fenders (fenders heavily padded with thick telephone books of course) and remove the subframe while the engine remains in the car. If you wind up removing the subframe, that would be a good time to replace any bad mounts. Good Luck.

Happy Motoring, Mark
__________________
DrDKW

Last edited by Mark DiSilvestro; 01-14-2004 at 07:26 PM.
Reply With Quote
  #4  
Old 01-14-2004, 07:59 PM
300SDog's Avatar
gimme a low-tech 240D
 
Join Date: Jan 2003
Location: central ky
Posts: 3,602
If this ever happens at all, it's usually on account of rust - say on early Ponton models or even the 116 that also suffered rust.

I hate to say this, but you should probably be thinkin about getting another 114....... or takin the car to combination welder/mechanic who knows how to remove and reinstall the A-frame and make the weld stick like glue - all for whatever reasonable price you are willing to pay.
Reply With Quote
  #5  
Old 01-14-2004, 08:08 PM
Registered User
 
Join Date: May 2003
Posts: 7
Another pic. From the rear looking forward.
Attached Thumbnails
How to fix a broken control arm pivot?-broken-benz-6-resized.jpg  
Reply With Quote
  #6  
Old 01-14-2004, 09:11 PM
Registered User
 
Join Date: Jan 2001
Location: Alexandria, Virginia
Posts: 5,480
In 1976, I had a similar problem, the failure of the threaded subframe steering box mounts on my '61 Ponton 180b. My factory Ponton shop manual stated that if there was any doubt as to being able to reliably repair the subfame, it should be replaced.
Yours looks like a fatigue failure, not rust.
The crossmember/subframe is detachable, not part of the unibody so, worst case scenario, you'll have to replace it with a good used or new one.

Happy Motoring, Mark
__________________
DrDKW

Last edited by Mark DiSilvestro; 01-14-2004 at 09:19 PM.
Reply With Quote
  #7  
Old 01-14-2004, 11:59 PM
Registered User
 
Join Date: May 2003
Location: Boonville Indiana
Posts: 2,342
Location

Where are you located....I have a 115 that can be had very reasonable.....
__________________
James A. Harris
Reply With Quote
  #8  
Old 01-15-2004, 11:13 AM
Registered User
 
Join Date: Aug 2001
Location: Evansville, Indiana
Posts: 8,150
You also need to replace all the control arm bushings -- the one in the pic is missing most of the rubber, and probably the fracture was a result of the bolt and sleeve banging around inside the hole.

Peter
__________________
1972 220D ?? miles
1988 300E 200,012
1987 300D Turbo killed 9/25/07, 275,000 miles
1985 Volvo 740 GLE Turobodiesel 218,000
1972 280 SE 4.5 165, 000 - It runs!
Reply With Quote
  #9  
Old 01-15-2004, 12:39 PM
dmorrison's Avatar
Registered User
 
Join Date: Dec 2002
Location: Colleyville, Texas
Posts: 2,695
I feel for you. This is the same way I learned to weld. My son got his 65 Mustang and after taking it apart I discovered that I had to weld about 12 sections of the car. This looks to me like it can be repaired. I would consider completely removing the mount from the subframe ( if this car is a subframe moount setup other wise your forced to repair the mount ) so you can check the interior of the subframe. It may need some rust treatment. And then reattach the mount by welding it back on.

Another option is to of course find another subframe mount and just swap it out.

Try to find a good restoration shop in your area and they will be set up for repairing the subframe. Or I recommend Lincoln electric, Hobart or a Miller welder. I have the LE weld pack 100 with gas conversion. If your going to do your own welding go with a good name brand welder not a knock off. It will last forever and you'll be happy with it. Don't over buy a welder. I was going to buy a LE unit that was 2 steps up. when I called LE to ask some questions the salesman talked me down to the bottom unit. I have been able to weld anything I have and some freinds stuff on his Mustang and Corvette without any problems.

Dave
__________________
1970 220D, owned 1980-1990
1980 240D, owned 1990-1992
1982 300TD, owned 1992-1993
1986 300SDL, owned 1993-2004
1999 E300, owned 1999-2003
1982 300TD, 213,880mi, owned since Nov 18, 1991- Aug 4, 2010 SOLD
1988 560SL, 100,000mi, owned since 1995
1965 Mustang Fastback Mileage Unknown(My sons)
1983 240D, 176,000mi (My daughers) owned since 2004
2007 Honda Accord EX-L I4 auto, the new daily driver
1985 300D 264,000mi Son's new daily driver.(sold)
2008 Hyundai Tiberon. Daughters new car
Reply With Quote
  #10  
Old 01-15-2004, 04:31 PM
Registered User
 
Join Date: May 2003
Posts: 7
Peter,
That makes sense. No wonder the subframe broke. I'll get some bushings on order from Claridges.

Dave,
I'm going to rent a wire feed unit from Home Depot. They have 'em for 30 bux a day. Probably have to buy a spool of wire too. I'll spend half a day practicing on scrap, then go for it.
Thanks for the encourgement.

MOOSE
Reply With Quote
  #11  
Old 01-15-2004, 06:18 PM
300SDog's Avatar
gimme a low-tech 240D
 
Join Date: Jan 2003
Location: central ky
Posts: 3,602
Or replacing the entire subframe might be path of least resistance instead of making welds that might not hold.... Hell, at good junkyard you could probably walk away with fresh A-frames too.... and they will cut the replacement subframe out in matter of maybe 30 minutes otherwise itsa bolt on part when you go to install it.

Long time ago, i was dealing with broken rear subframe on 114.... the huge wishbone looking thing that holds rear suspension to the unibody. Believe it or not - it was notso difficult to replace. Toughest part was dealing with coil spring compressor.
Reply With Quote
  #12  
Old 01-16-2004, 02:26 AM
wbain5280's Avatar
Registered User
 
Join Date: May 2001
Location: Northern Va.
Posts: 3,386
I hope you're not driving the car. While you're working on the subframe, check for oil leaks as well.

__________________
Regards

Warren

Currently 1965 220Sb, 2002 FORD Crown Vic Police Interceptor

Had 1965 220SEb, 1967 230S, 280SE 4.5, 300SE (W126), 420SEL

ENTER > = (HP RPN)

Not part of the in-crowd since 1952.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 10:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page