Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes ShopForum > Technical Information and Support > Vintage Mercedes

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 01-31-2007, 01:46 PM
Registered User
 
Join Date: Jun 2005
Posts: 19
1972 250C fender removal

Hello,

I need to remove my left front fender from my 72 250C (wife bashed it backing out of garage). It looks like it will bolt off quite easily but I have heard horror stories about the adhesive they used back in the 70s to bond the sheet metal together at the seams. Does anybody have any experience with fender removal from this era of cars and if so are there any issues that I should consider before embarking on this project.

Thanks
Reply With Quote
  #2  
Old 01-31-2007, 03:19 PM
300SDog's Avatar
gimme a low-tech 240D
 
Join Date: Jan 2003
Location: central ky
Posts: 3,602
Propane torch and putty knife will beat the glue. You can use any type of caulking for the new fender, its a good idea to have it sealed. And the toughest bolts to reach are in the upper door hinge area. Start will pulling the bumper and headlight, working slow and steady it wont take more then a day.
Reply With Quote
  #3  
Old 01-31-2007, 08:06 PM
Registered User
 
Join Date: Nov 2004
Location: Nova Scotia, Canada.
Posts: 6,510
The last front fender I changed on a 1972 250c had no bonding agent at all.. It may have been changed once before for all I know though. If you detect a bonding sealant a propane torch should soften it up in small areas as you work along separating it.
Since the fender you are removing is junk I guess bending the flange back to provide separation if required should do no damage. I think I remember one fastening bolt very high on the back edge of the fender though but might be mistaken. Keep an eye out for it.
It has been a long time since I changed that fender remember so allow a little. The main thing I wanted to mention. There has not been a lot of happiness with the Danish aftermarket replacement fenders that are available. The profiles are good I believe but the gauge of metal is too thin. A good used one if you can find it is much better just in my opinion again.
Do not be too upset with the wife. She probably feels bad enouigh already. Count your blessings. It could have been the rear quarter or the whole side. Maybe next time? :
Reply With Quote
  #4  
Old 02-01-2007, 10:31 AM
Benzcrusher's Avatar
Registered User
 
Join Date: Jan 2004
Location: Upstate SC
Posts: 1,114
Make sure you have removed all of the bolts and screws first including the rubber block on the inside ridge which buffers the hood. Remove the reveal panel in the wheel well, there are 3? 10mm head screws in there, the left side (drivers) is a ***** because there is a vacuum resivoir mounted in there, to un-bolt that, the nuts are inside the car behind the hood release, behind the tar felt layer.
You'll need to remove the long chrome trim on the rocker, under it are 2 #3 screws holding the lower "ear" of the fender. Don't be suprized if you find all kinds of rust there... Replace the screws with stainless ones.
Using a torch ( I use a cutting torch with a fine tip) heat the inside seam, using care because the filler is flamable. Now quickly run a carpet knife (sturdy old-style) in the crotch of that seam. Continue with the heat and cuts until you can tug on the fender with upward force to have it come free....
__________________
"Shabby" 1978 240D with a 300D motor
1997 Volvo 960 wagon 245K
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 12:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2011 Pelican Parts - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page