=====DIY 617.9XX prechamber tools ===== ====on the OM617.9xx engine==== ===by ""Diesel Head""=== ===Instructions revised by ""whunter""=== ===12/11/07=== ---- The following is a recap with pictures of all the tools that can be made very easily at home to remove the injectors, prechamber collers and prechambers on a 617.9xx engine. All tools worked exceptionally well and some of the ideas came off this site from previous threads, however I was not able to find pics (that does not mean they are not there). The entire job after the tools were made took roughly 4 hours and went very smoothly. The only hitch was with the collars, 2 of them came out easily with the homemade tool, the remaining 3 had to be loosened with a hammer and chisel because the collar started to break apart using the tool. During assembly the tool worked like a charm. Feel free to PM me if any additional details are needed. To remove injectors, I used an old cornwell deep impact socket 1 1/16 and used a carbide bit to grind down the interior walls to accommodate the injector weep ports. This took about 20 minutes.......Cost $0 plus labor. To remove prechamber collars, I used an old cornwell 7/8 shallow impact socket and used a cut off wheel on a die grinder to cut notches that fit in groves of collar. This took about 5 minutes.....Cost $0 plus labor. It was also helpful to use the bicycle crank tool installed into the collar (just happened to fit the 7/8 socket perfectly) to stabilize the socket so it would not slip out of the groves. To remove prechambers, I used a slide hammer purchased at a local tool shop for $10 and using info from this site I went to the local cycle shop and purchased a bicycle crank extractor tool for $20. Using a cut off wheel on a die grinder I removed the crank handle and took the rest to a local welding shop where they welded the inner bolt of the crank tool to a part of the slide hammer for $10. ---- http://www.peachparts.com/diy/om617prechambertools/01.jpg http://www.peachparts.com/diy/om617prechambertools/02.jpg http://www.peachparts.com/diy/om617prechambertools/03.jpg http://www.peachparts.com/diy/om617prechambertools/04.jpg http://www.peachparts.com/diy/om617prechambertools/05.jpg ---- Here are more pics http://www.peachparts.com/diy/om617prechambertools/06.jpg http://www.peachparts.com/diy/om617prechambertools/07.jpg http://www.peachparts.com/diy/om617prechambertools/08.jpg http://www.peachparts.com/diy/om617prechambertools/09.jpg http://www.peachparts.com/diy/om617prechambertools/10.jpg ---- A few more pics http://www.peachparts.com/diy/om617prechambertools/11.jpg http://www.peachparts.com/diy/om617prechambertools/12.jpg http://www.peachparts.com/diy/om617prechambertools/13.jpg http://www.peachparts.com/diy/om617prechambertools/14.jpg ---- __**For those needing or wanting instructions.**__ **#0.** Take pictures for reassembly and routing, BEFORE work begins. **#1.** Pull throttle linkages off and out of the way. **#2.** Remove the STEEL Injector lines from injectors and injection pump, flip the line set up side down, cover the line ports to protect against dirt/grit, and set aside. **#3.** Cover the injection pump delivery valve ports against grit/dirt. **#4.** Remove the injectors. **#5.** Remove the injector heat shields (I used an old dental pick to remove the shield). **#6.** Remove glow plugs, brace the wire harness connector so it does not twist off. **#7.** Remove prechamber collars. **#8.** Screw tool into prechamber and extract using slide hammer (Mine took about 10 smacks each, some prechambers have been known to require heavier force). **#9.** **WARNING:** Make sure prechamber seal ring is also removed. **#10.** Clean out any carbon / soot / dirt, use a vacuum cleaner with a wide bore drinking straw taped to the nozzle for reaching into the cylinder. **#11.** WARNING: You MUST install a NEW prechamber seal ring every time the prechamber is removed, this is a single crush seal… OM617 part numbers are: Standard seal ring MB# 6150170060 Repair size I; 2.3mm MB# 6150170160 Repair size I; 2.6mm MB# 6150170260 Repair size I; 2.9mm MB# 6150170360 **#12.** Using a good used or new prechamber, thread tool into prechamber and tap into place firmly. OM617 prechamber number is: MB# 6170100352 **#13.** Install new collar OM617 prechamber collar number is: MB# 6150170003 **#14.** Install new glow plugs, **WARNING/DANGER:** you can break the tapered seat in cylinder head with excess force. **#15.** Install a NEW heat shield. **WARNING:** You MUST install a NEW heat shield every time the Injector is removed, this is a single crush seal… **#16.** Install wires onto glow plugs. **WARNING/DANGER:** This is an electric connection, the eight millimeter nut should be tightened with a wrench, and final torque is applied using one finger tip = any more force will damage or break the electrode = destroy your new glow plugs. **#17.** Install STEEL injector lines, and looped fuel return hoses. **#18.** Install throttle linkage. **#19.** Prime the fuel system one hundred strokes. **#20.** Start the engine. **#21.** Use 50/50 solution of dish soap/water to inspect for prechamber combustion leaks. ---- [[http://www.peachparts.com/shopforum/showthread.php?t=207782 Discuss this DIY here.]] **-""Diesel Head""** ---- CategoryDiy