pulled the grease cap off this weekend so I could do the bearings. The cap has a small hole along the edge

What is this hole for? how does the grease not ooze out or water & dirt get in? Where should the hole be? I can rotate the cap to point the hole up, down, forward or back.

__________________
1987 300TDT
1981 VW MKI Caddy 1.6 diesel, waiting on engine swap
1983 D-50 Power Ram 4x4 "Mitsubishi" 2.3 turbo diesel
assorted gas powered crap and motorcycles

RIP: 1984 300TDT, 1982 300TDT, 1984 190D 2.2, 1992 300D 2.5, 1987 300TDT, 1982 Maxima LD28, 1983 Maxima LD28, Isuzu C223 P'ups X3, 1983 Holiday Rambler 6.2 Banks turbo diesel, 1984 Winnebago LeSharo 2.1 TD, 1985 Allegro 6.5

Are you sure? My W116 had no hole in the cap. Anywhere.

The cap should be fully seated. and as the wheel rotates it will be up, down and everwhere in between.

__________________
Proud owner of ....
1971 280SE W108
1979 300SD W116
1983 300D W123
1975 Ironhead Sportster chopper
1987 GMC 3/4 ton 4X4 Diesel
1989 Honda Civic (Heavily modified)
---------------------
Section 609 MVAC Certified
---------------------
"He who fights with monsters might take care lest he thereby become a monster. And if you gaze for long into an abyss, the abyss gazes also into you." - Friedrich Nietzsche

I never noticed a hole in mine when I pulled them off. I wasn't looking for one either but I'm pretty sure there was not one there. Do both your caps have holes?

Scott

__________________
Scott
1982 Mercedes 240D, 4 speed, 275,000
1988 Porsche 944 Turbo S (70,000)
1987 Porsche 911 Coupe 109,000 (sold)
1998 Mercedes E300 TurboDiesel 147,000 (sold)
1985 Mercedes 300D 227,000 (totaled by inattentive driver with no insurance!)
1997 Mercedes E300 Diesel 236,000 (sold)
1995 Ducati 900SS (sold)
1987 VW Jetta GLI 157,000 (sold)
1986 Camaro 125,000 (sold - P.O.S.)
1977 Corvette L82 125,000 (sold)
1965 Pontiac GTO 15,000 restored (sold)

W123, 82TD wagon

The hole is in the groove that goes around the cap. The hole is about the size of a small drill bit or ball point pen tip.

I note has noticed it but I was cleaning the outside of the cap and scraped a little bit of gunk out of the groove. The gunk was a little dab of grease.

Your right, the cap does spin around. For a minute I was thinking the hub was fixed and the rotor spun but the cap is on the rotor.

The hole looks intentional, not damage or drilled after the fact. I didn't check the other cap. I put it all back together as I am now waiting on new ball joints and will do everything at once.

__________________
1987 300TDT
1981 VW MKI Caddy 1.6 diesel, waiting on engine swap
1983 D-50 Power Ram 4x4 "Mitsubishi" 2.3 turbo diesel
assorted gas powered crap and motorcycles

RIP: 1984 300TDT, 1982 300TDT, 1984 190D 2.2, 1992 300D 2.5, 1987 300TDT, 1982 Maxima LD28, 1983 Maxima LD28, Isuzu C223 P'ups X3, 1983 Holiday Rambler 6.2 Banks turbo diesel, 1984 Winnebago LeSharo 2.1 TD, 1985 Allegro 6.5

My initial thought was that someone punched a hole in it by accident. Now that you mention it's near the edge, it seems even more so.

Check your other ones to see what they look like. I can't recall ever seeing a cap with a hole in it.. Wouldn't make sense to have a hole, since the grease would heat up and leak out.

I'm sure someone removed the cap with a sharp tool (scratch awl or nail set) and slipped. I have removed mine with a nail set and hammer before (when it was the only thing handy) and had I slipped with the nail set, it would have probably punched a hole exactly where yours is.

Neal

__________________
'83 300SD 335,000km (207k) mi SOLD
'87 560SL 163,000km (101k mi) SOLD
'86 300SDL 356,000km (220k mi) SOLD
'92 500SEL 250,000km (155k mi) SOLD
'90 300SL 140,000km (87k mi) SOLD
'01 S430 260,000km (161k mi) SOLD
'03 SL500 167,000km (104k mi) SOLD
'07 S550 4MATIC 235,000km (146k mi) SOLD
'07 GL320 CDI 4MATIC 348,000km (215k mi)
'13 GL350 BlueTec 4MATIC 170,000km (105k mi)
'14 SL550 72,000km (43k mi)

If my part come in by the weekend I'll get back to the caps.

Worst case is I just swap caps with my parts car

__________________
1987 300TDT
1981 VW MKI Caddy 1.6 diesel, waiting on engine swap
1983 D-50 Power Ram 4x4 "Mitsubishi" 2.3 turbo diesel
assorted gas powered crap and motorcycles

RIP: 1984 300TDT, 1982 300TDT, 1984 190D 2.2, 1992 300D 2.5, 1987 300TDT, 1982 Maxima LD28, 1983 Maxima LD28, Isuzu C223 P'ups X3, 1983 Holiday Rambler 6.2 Banks turbo diesel, 1984 Winnebago LeSharo 2.1 TD, 1985 Allegro 6.5

I simply use a large pair of channel locks to take them off. What do most people do?

Scott

__________________
Scott
1982 Mercedes 240D, 4 speed, 275,000
1988 Porsche 944 Turbo S (70,000)
1987 Porsche 911 Coupe 109,000 (sold)
1998 Mercedes E300 TurboDiesel 147,000 (sold)
1985 Mercedes 300D 227,000 (totaled by inattentive driver with no insurance!)
1997 Mercedes E300 Diesel 236,000 (sold)
1995 Ducati 900SS (sold)
1987 VW Jetta GLI 157,000 (sold)
1986 Camaro 125,000 (sold - P.O.S.)
1977 Corvette L82 125,000 (sold)
1965 Pontiac GTO 15,000 restored (sold)

I do that too now, but used to use a thin screwdriver to pry off the cap.

__________________
'83 300SD 335,000km (207k) mi SOLD
'87 560SL 163,000km (101k mi) SOLD
'86 300SDL 356,000km (220k mi) SOLD
'92 500SEL 250,000km (155k mi) SOLD
'90 300SL 140,000km (87k mi) SOLD
'01 S430 260,000km (161k mi) SOLD
'03 SL500 167,000km (104k mi) SOLD
'07 S550 4MATIC 235,000km (146k mi) SOLD
'07 GL320 CDI 4MATIC 348,000km (215k mi)
'13 GL350 BlueTec 4MATIC 170,000km (105k mi)
'14 SL550 72,000km (43k mi)

I use a claw hammer with straight claws to remove the hub caps. Works good.

P E H