PeachParts Mercedes-Benz Forum

PeachParts Mercedes-Benz Forum (http://www.peachparts.com/shopforum/index.php)
-   Diesel Discussion (http://www.peachparts.com/shopforum/forumdisplay.php?f=15)
-   -   engine wont shut off... (http://www.peachparts.com/shopforum/showthread.php?t=157415)

Flanagan 07-01-2006 07:23 PM

engine wont shut off...
 
whenever i turn my key to turn the engine off, the engine just keeps running so i have to go under the hood and manually cut it off with the "STOP" lever. why is this happening?

thanks

Endust 07-01-2006 07:55 PM

Most likely a vaccum leak. You didnt specify year or model but generaly when you turn the switch to STOP you send a vaccum signal to the back of the injection pump that cuts the fuel. Look on the back of the pump for a brown vac tube and make sure its hooked up. If it is, then pull it off and apply vac to the port on the IP. It should hold vac. If it doesnt, you need a new diaphragm. Next check for vac on the brown tube.

Flanagan 07-05-2006 02:11 PM

sorry, is a 1985 300D...ill try to find the brown vac line, thanks

Maroon 300D 07-05-2006 02:23 PM

Quote:

Originally Posted by Endust
Most likely a vaccum leak. You didnt specify year or model but generaly when you turn the switch to STOP you send a vaccum signal to the back of the injection pump that cuts the fuel. Look on the back of the pump for a brown vac tube and make sure its hooked up. If it is, then pull it off and apply vac to the port on the IP. It should hold vac. If it doesnt, you need a new diaphragm. Next check for vac on the brown tube.

Remember, these are just some of the first things to test. The vac leak could potentially be anywhere in the system. If you have other vacuum-related problems, it's probably a clue as to where the leak is. There's lots of info. on how to test the system if you do a search. Diesel Giant also has a pictorial on it; if you haven't seen that, I suggest you check out www.dieselgiant.com.

rkerste219 07-06-2006 09:44 PM

after reading this, I tried the red manual stop on my 240D (1981), it slows down, but will not stop.

do I need sometype of adjustment to the linkage?

bob 1981 240d

nhdoc 07-06-2006 10:07 PM

Quote:

Originally Posted by rkerste219
after reading this, I tried the red manual stop on my 240D (1981), it slows down, but will not stop.

do I need sometype of adjustment to the linkage?

bob 1981 240d

Yes, your linkage is not adjusted correctly...you should be able to stop it with the lever...sometimes you have to push hard but if it doesn't stop it means the length of the rods are not adjusted properly and the linkage it is hitting the stop before the fuel cutoff is completed.

Endust 07-06-2006 11:07 PM

The thing about the stop is that its not a "hard" stop. The idle screw is actualy spring loaded at the tip. You need to push the lever hard enough to hit the stop and then compress the pin. If the pin is rusted it may not work and you wont be able to use the lever for shut down till you free it. The other possibility is that your idle is turned up so high that even compressing the tip of the screw all the way doesnt force the rack closed. Check that idle stop screw and one way or the toher youll find you probkem.


All times are GMT -4. The time now is 02:20 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website