|
|
|
#1
|
|||
|
|||
Outside thermometer
How hard is it to replace an outside thermometer on a 1995 300e diesel. Also is the thermometer just for a 1995 300e or will thermometers from other models and makes fit and work. I think the sensor in the cluster is ok, but it is blank now. This past summer I got in the car and noticed the outside temp as being 136 degrees and it would vary some from that but not a whole lot. Then the sensor in the cluster went blank.
Thanks L L L |
#2
|
|||
|
|||
The sensor is behind the front license plate or the drivers side behind the bumper. The display is in the cluster. Jeremy 5848 recently posted an excellent tutorial on the workings of the outside temperature display/sensor. Look it up. It should help you determine which part has failed.
__________________
1987 300D 146K Original #14 Head One eye on the road, the other on the temp. gauge Gone But Not Forgotten 1983 380 SEL Long gone 1983 300SD Wish I hadn't traded it in on a 90' Corvette 1989 300SE My all time favorite 1995 E420 Went like a bullet |
#3
|
||||
|
||||
To replace the sensor and the entire wire would be rather difficult as it's wrapped in several different wire bundles as it travels from the sensor, under the license plate, up the driver's side fender, through the fuse box, and into the cabin. You can cut the sensor off, and wire in a replacement. If the display is blank I'd make sure it's getting power. Usually when they sensor goes bad or is disconnected the display will read to one extreme or the other, can't remember which. The sensors are the same across the years and models. The sensor itself looks a little different but they all work the same. Any of the 126 or 124 chassis sensors will work. I used to have a couple extra with just a little wire on them if you want one let me know. If I still have it's yours if you pay shipping. I'll look today to see if I can find one.
__________________
Andrew '04 Jetta TDI Wagon '82 300TD ~ Winnie ~ Sold '77 300D ~ Sold
|
#4
|
|||
|
|||
Here is Jerremy`s thread
http://www.peachparts.com/shopforum/showthread.php?t=289232 Andrew, why don`t you put the display in Flow? Deliveryvalve has a good DIY installing one in a W123. There might also be some info helping Larrylarkin. http://www.peachparts.com/shopforum/showthread.php?t=251755 Charlie
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
#5
|
||||
|
||||
Quote:
I've got at least one more display and sensor in my parts pile, and I used to have a few short sensor wires. If someone wants the display and sensor let me know.
__________________
Andrew '04 Jetta TDI Wagon '82 300TD ~ Winnie ~ Sold '77 300D ~ Sold
|
#6
|
|||
|
|||
I have been going to install one in the 85. have a couple of the wiring harnesses and several of the displays, from the 126, then when Richard found the 124 fit better, starting removing them too. Don`t know if any work, but I got em.
Charlie
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
#7
|
||||
|
||||
Yes the 124 display fit better. I've had both in Flo. Originally I had the 126 display. But later found a 124 display and put it in.
Larry, I just looked through my stuff. I've got several sensors. Let me know if you want one.
__________________
Andrew '04 Jetta TDI Wagon '82 300TD ~ Winnie ~ Sold '77 300D ~ Sold
Last edited by Biodiesel300TD; 01-30-2011 at 03:17 PM. |
#8
|
|||
|
|||
Biodiesel300td I would like for you to send me a sensor. Just let me know how you want
the money for the shipping or you can ship it collect. I will pay you for the part if you like! The best way to ship would be for you to get the money from me and then ship. Can you estimate the shipping charge and I will send you the money if you tell me where to send it or whatever you want to do. Thanks L L L |
#9
|
|||
|
|||
Biodiesel300td:
Received your personal message and sent a reply that I hope you got. I do not know how to get around in this forum. Sorry!!! If you didn't receive the reply let me know? |
Bookmarks |
|
|