|
|
|
#1
|
||||
|
||||
Bloody Climate Control !
Ok, so I'm trying to get through the checklist on my 1985 380SE Diesel (converted), I've been trying to get the heat to work properly, I'd also like to fix the A/C but figure thats a waste of time until the rest of the system functions correctly. I had asked this question a while back somewhere else but seemed to hit a dead end with no further instructions. So without further adieu, the issue at hand.
Symptoms: 1. Blower will not start unless Bi-level, or Defrost are selected first. After one of them has been pushed the other two setting will work, as will the automatic and hi\low settings. 2. regardless of the setting selected, none of the vents change. Seems the vents will not change from the defrost setting. 3. Temp wheel functions as it should (sort of) and blower speeds up and slows down in relation to its position. I have noticed that after full heat it doesn't like to go full cold. Thinking this ties into symptom 2 and guessing that the heat flap isn't closing. Actions taken so far: 1. CCU unit first re-soldered, and then changed out with a unit from the wreckers with no change in symptoms. 2. Mono valve replaced with good unit from the wreckers. Thats how I got heat. 3. Tested Pods from gang valve, these were the initial results: 1: holds at 20inhg 2: Bleeds quickly down to 10inhg and holds 3: can only pump up to 5inhg and then drops to ~2-3 and holds 4: holds at 20inhg 5: Bleeds quickly to 0 6: bleeds slowly to 4inhg and then holds I replaced the recirc and fresh air actuators, and the legflap one doesn't seem to leak anymore so that should all be good. But I'm still having problems. The system still will not activate unless on bilevel or defrost, and it still will not open or close flaps. The heat works on defrost, or somewhat on bi-level. On bilevel it doesn't seem to heat well, it warms slightly as I turn the the dial up, then when I click it over to max I get excellent heat. So there's still something amiss. But this is not consistent. Somedays it heats adequately other days I freeze, then still on others (less often than the other two) I bake... More often than not though it just seems to heat feebly. I'm beginning to think that it could be the climate control amp or something to do with the whatever is supposed to keep the system from turning on before the coolant gets warm. Since this was a gasser at one point and had some of the harnesses changes when it became a diesel I'm also wondering if there is anything that could have been disconnected. Any Ideas????
__________________
2004 F150 4.6L -My Daily 2007 Volvo XC70 -Wife's Daily 1998 Ford F150 -Rear ended 1989 J-spec 420SEL -passed onto its new keeper 1982 BMW 733i -fixed and traded for the 420SEL 2003 Volvo V70 5 Speed -scrapped 1997 E290 Turbo Diesel Wagon -traded for above 1992 BMW 525i -traded in 1990 Silver 300TE -hated the M103 1985 Grey 380SE Diesel Conversion, 2.47 rear end, ABS -Sold, really should have kept this one 1979 Silver 300D "The Silver Slug" -Sold |
#2
|
||||
|
||||
Quote:
You have verified leaking actuators, and fixed some, but what supply vacuum do you have in inches/Hg when running? You need a minimum of 10-16" to function properly. Any leakage will hamper the function of the system. Also, I suspect your temp sensor chain (inside, ambient outside). A thorough read of the manual may illuminate you to the workings of your system, and should be available online. If not, you can glean a great deal from the R107 AC III info, which is the system I am most familiar with. It is available online at startek, MB's website. Look at Benzworld.org - Mercedes-Benz Discussion Forum in the 107 forum for the stickie, EGv107 for a link to teh online manual, then navigate to any of the 560Sl's for a good read on the Ac III system.
__________________
RM Smith 1988 560SL "Where is it again that we are going, and why are we in this handbasket"? |
#3
|
|||
|
|||
Quote:
Did these actions result in a "Known Good CCU"™? Popping in a finely aged and pickled unit from the wreckers is about as effective as stabbing the original with a soldering iron. So, until you are working with a "Known Good CCU"™ your troubleshooting is an exercise in futility.
__________________
'83 SD, 2x '85 SD You are entitled to your own opinions, you are not entitled to your own facts. |
#4
|
|||
|
|||
my ccu started doing some of these same things a while back. must be a local thing
i don't have the patience to try and bother with it as far as you have. good on ya!
__________________
1981 300SD - 283,000 KM's at purchase, 360k+ now. Engine replaced at 311k. 16" CLK wheels, w126 gen II cosmetic upgrades, late w126 leather interior. RIP. Parted and gone due to fire 1987 300SDL - 243K miles and counting. In winter hibernation! 2001 Ford F250 Super Duty "Platinum Edition" Lariat 4x4 7.3L turbo diesel, 295k+ miles, various mods for reliability and performance. |
#5
|
||||
|
||||
@WDBCB20 I realize it it technically possible for both the board I re-soldered and the one form the wreckers to be faulty. But it just seemed unlikely that both would display the exact same symptoms. Thats why I was leaning toward it being something else.
__________________
2004 F150 4.6L -My Daily 2007 Volvo XC70 -Wife's Daily 1998 Ford F150 -Rear ended 1989 J-spec 420SEL -passed onto its new keeper 1982 BMW 733i -fixed and traded for the 420SEL 2003 Volvo V70 5 Speed -scrapped 1997 E290 Turbo Diesel Wagon -traded for above 1992 BMW 525i -traded in 1990 Silver 300TE -hated the M103 1985 Grey 380SE Diesel Conversion, 2.47 rear end, ABS -Sold, really should have kept this one 1979 Silver 300D "The Silver Slug" -Sold |
#6
|
|||
|
|||
That's a CCU relay problem. Cleaning the contacts on the relays is a good place to start.
__________________
When cryptography is outlawed, bayl bhgynjf jvyy unir cevinpl. |
#7
|
|||
|
|||
To save yourself some time and money I would send the push button assembly to GDL. Definitely don't buy a new one. I did and 5 years later I have the same problem you mention. I've got faith in Peter that he can fix it in such away that it will not break again and it will probably be cheaper than any other choice.
If you are able to get one working let me know how you did it. I've tried resoldering and cleaning the relays to no avail.
__________________
1984 300 SD 384,000 Miles |
#8
|
||||||||||
|
||||||||||
Its amazing how many folk will gravitate to the most expensive item on the list and declare, "That is it..." Maybe it is, but you got other problems to sort out first that have NOTHING to do with the blower/panel function. You got to fix/plug the vacuum issues first!
Let me re-address acouple of issues directly, assuming ACC III: Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Granted most of my knowledge comes from rebuilding a 107 system, but I researched others during the project. All I wrote above is rubbish if you have the AC II system with the amp and servo.... well, not all. Best of luck to you...
__________________
RM Smith 1988 560SL "Where is it again that we are going, and why are we in this handbasket"? |
#9
|
|||
|
|||
The described symptoms do not implicate the low temp lockout switch. They are a perfect fit with a CCU relay issue.
__________________
When cryptography is outlawed, bayl bhgynjf jvyy unir cevinpl. |
#10
|
||||
|
||||
I think the manual disagrees with your statement concerning the lockout switch... of course, this is from the ACC III for the 107...
__________________
RM Smith 1988 560SL "Where is it again that we are going, and why are we in this handbasket"? |
#11
|
|||
|
|||
Quote:
I had the same issue even though my cutout switch is bypassed to a permanent ground. Cleaning the relay contacts solved the problem.
__________________
When cryptography is outlawed, bayl bhgynjf jvyy unir cevinpl. Last edited by tangofox007; 03-24-2012 at 11:17 AM. |
#12
|
||||
|
||||
Quote:
I'm thru with this... I'm not gonna debate "start" and "run", etc. The manual goes on to say if def selected first, then the other fan functions will work. Regardless, your experiences may prove to be his problem, although he has a lot more going on that need correcting... Peace-Out
__________________
RM Smith 1988 560SL "Where is it again that we are going, and why are we in this handbasket"? |
Bookmarks |
|
|