|
|
|
#1
|
||||
|
||||
Correct O-Ring for OM617 Fuel Filter Bolt
Gents, I can't seem to get the correct O-Ring for my fuel filter bolt. This is the fourth or fifth time I've had it off in the last month.
The pictures show the two O-Rings I ordered. One was too small, one too large. The picture also shows that I have the bracket of part # 6150920108, which I understand has a bearing on the type of bolt and therefore the type of O-ring to order? Any help on the correct O-Ring would be appreciated. The copper crush washer I received was the correct size, although the original washer was aluminum.
__________________
i know Jim Smith. i don't actually know him, but I know of him
http://imageshack.com/a/img923/6201/RQ1H6A.jpg |
#2
|
|||
|
|||
The 003 997 58 48 part number should be the correct size for your fuel hollow bolt.
When installed it may look undersize, that's just because the old one has become deformed over time The size of the proper o-ring for your application is 2mm for the cross section and 10mm for the inner diameter.
__________________
78 W116 300SD 'Desert Rose' new as of 01/26/2014 79 W116 300SD 'Stormcloud' RIP 04/11/2022 |
#3
|
||||
|
||||
This is what is in my notes:The 10mmIDx17mmODx2.5mm thick fits the bottom of the Fuel Filter Bolt
__________________
84 300D, 82 Volvo 244Gl Diesel |
#4
|
||||
|
||||
Thanks guys. Apparently I bought and have the correct part, I just need to stretch it over the bolt and let nature take its course
__________________
i know Jim Smith. i don't actually know him, but I know of him
http://imageshack.com/a/img923/6201/RQ1H6A.jpg |
#5
|
|||
|
|||
I'm thinking I ordered the correct o-ring then discovered that the harbor freight metric set contains extras. There was also something for the shaft of the oil filter cover.
|
#6
|
|||
|
|||
hi,
top o ring on the fuel filter bolt i've read is 14mm ID x 19mm OD x 2.5mm which is in my kit. but i've seen 2 measurements offered for the bottom o ring on the fuel filter bolt: 10mm ID x 17mm OD x 2.5mm thick and 10mm ID x 15mm OD x 2.5mm thick does anyone know which of the 2 is correct? the 17mm one isn't in my o ring kit! thanks
__________________
w123 1985 300D turbo sept 2015 - present 1985 300TD turbo oct 2023 - present looking for biodiesel in nyc |
#7
|
||||
|
||||
Quote:
000-997-00-48 003-997-58-48 These will fit exactly as you need and you can get them from the dealer or research further to find the sizes. |
#8
|
||||
|
||||
Quote:
__________________
Current stable: 1995 E320 149K (Nancy) 1983 500SL 120K (SLoL) Black Sheep: 1985 524TD 167K (TotalDumpster™) Gone but not forgotten: 1986 300SDL (RIP) 1991 350SD 1991 560SEL 1990 560SEL 1986 500SEL Euro (Rusted to nothing at 47K!) |
#9
|
|||
|
|||
ah yes that makes sense, just wanted to make sure there wasn’t some kind of thicker flatter o ring that ended up 17mm, cause i saw that size claimed as the right size more times on the forums than the 15mm size!
so the final correct o ring sizes for the fuel filter bolt are: top: 14mm ID x 19mm OD x 2.5mm bottom: 10mm ID x 15mm OD x 2.5mm thanks. there’s loads of info in these forums, but most isn’t ever compiled into an organized way, there could be a full peach parts user manual with easy to look up specs updated for 2019!
__________________
w123 1985 300D turbo sept 2015 - present 1985 300TD turbo oct 2023 - present looking for biodiesel in nyc |
Bookmarks |
|
|