Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 06-04-2018, 06:01 PM
Registered User
 
Join Date: Dec 2015
Posts: 102
Head Gasket Leak goop? Bears True Blue? Bars? Is it nonsense?

Earlier I posted about my '83 240d that had an overheat event while my son was driving.

Bottom line, I'm pretty sure I have a blown head gasket (or maybe a cracked head). The engine runs fine, but after 5-10 minutes at medium rpm, it overheats. I have a large funnel that fits perfectly into the radiator neck. I filled with water while fast-idling the car, and after the stat opens, you see bubbles coming up out of the radiator every now and then. I believe this is exhaust gas.

Youtube is full of videos of people swearing by various head gasket leak sealers. Barrs, Bears True Blue, many others. I watched the Bears how-to video and they are quite specific on the process. It is not just dump it in there and forget it.

Have any of you had any experience with these products?

Reply With Quote
  #2  
Old 06-04-2018, 06:06 PM
Registered User
 
Join Date: Jan 2006
Location: Tucson, AZ
Posts: 5,358
Junk, especially so with the high compression diesels have.
__________________
“Whatever story you're telling, it will be more interesting if, at the end you add, "and then everything burst into flames.”
― Brian P. Cleary, You Oughta Know By Now
Reply With Quote
  #3  
Old 06-04-2018, 06:16 PM
Registered User
 
Join Date: Nov 2010
Location: TX
Posts: 3,978
using any of that will result in a very badly clogged cooling system.
__________________
2012 BMW X5 (Beef + Granite suspension model)

1995 E300D - The original humming machine (consumed by Flood 2017)
2000 E320 - The evolution (consumed by flood 2017)
Reply With Quote
  #4  
Old 06-04-2018, 06:44 PM
Diseasel300's Avatar
Registered User
 
Join Date: May 2016
Posts: 6,025
Pull the head and fix it properly. If you dump that stop-leak crap in your engine, you may as well save your money and tow it to the recycler now.
Reply With Quote
  #5  
Old 06-04-2018, 06:50 PM
Registered User
 
Join Date: Jun 2015
Location: PA
Posts: 398
Quote:
Originally Posted by Diseasel300 View Post
Pull the head and fix it properly. If you dump that stop-leak crap in your engine, you may as well save your money and tow it to the recycler now.
This x100.

It's a damn 240. It doesn't take much to pull the head at all.

Stop-leak junk is for beater cars that are knocking on the junkyards doorstep and you just need it to last another month or two.
__________________
'80 300SD - '83 240D - '00 E55 AMG - '02 G500
Reply With Quote
  #6  
Old 06-04-2018, 07:42 PM
Registered User
 
Join Date: Jan 2012
Posts: 7,534
Doing a leak down test to determine what cylinder is leaking to coolant then pulling the head is the best fix.

Pumping air into the cylinder and looking for bubbles in the radiator is _the only reliable way_ to confirm combustion to coolant leaks. Using a chemical test kit only finds large leaks and won't tell you what cylinder is leaking.

However, I have direct experience with many sealers across many cars.

Plain sealer won't work on a combustion chamber to coolant leak, they are for external leaks.

Bars Leaks tablets are fine for seepy external leaks but does nothing for combustion to coolant leaks. It is so good, GM and other auto makers recommend it for seepy leaks and sell it under their brand. This will not clog a cooling system that is in any decent condition and is stealth. It is a super fine powder containing mostly Ginger.

Blue Devil brand head gasket sealer will take a large head gasket leak to near nothing or zero. This contains Sodium Silicate ( AKA Water Glass ) This won't clog a cooling system either as Sodium Silicate remains suspended in water and only solidifies once the water is strained out by the leak.

BD will not work on a slight combustion to coolant leak. I've used this on an engine that used 1 qt coolant over a few months with minimal positive results. After pulling the heads, the gasket looked near perfect with very slight discoloration in one area. The heads had developed a very slight depression in one area resulting in less gasket clamping force. ( This was an iron block / head GM V6 )
Reply With Quote
  #7  
Old 06-05-2018, 09:40 AM
Registered User
 
Join Date: Dec 2015
Posts: 102
Quote:
Originally Posted by 97 SL320 View Post
Doing a leak down test to determine what cylinder is leaking to coolant then pulling the head is the best fix.

Pumping air into the cylinder and looking for bubbles in the radiator is _the only reliable way_ to confirm combustion to coolant leaks. Using a chemical test kit only finds large leaks and won't tell you what cylinder is leaking.

However, I have direct experience with many sealers across many cars.

Plain sealer won't work on a combustion chamber to coolant leak, they are for external leaks.

Bars Leaks tablets are fine for seepy external leaks but does nothing for combustion to coolant leaks. It is so good, GM and other auto makers recommend it for seepy leaks and sell it under their brand. This will not clog a cooling system that is in any decent condition and is stealth. It is a super fine powder containing mostly Ginger.

Blue Devil brand head gasket sealer will take a large head gasket leak to near nothing or zero. This contains Sodium Silicate ( AKA Water Glass ) This won't clog a cooling system either as Sodium Silicate remains suspended in water and only solidifies once the water is strained out by the leak.

BD will not work on a slight combustion to coolant leak. I've used this on an engine that used 1 qt coolant over a few months with minimal positive results. After pulling the heads, the gasket looked near perfect with very slight discoloration in one area. The heads had developed a very slight depression in one area resulting in less gasket clamping force. ( This was an iron block / head GM V6 )
Thanks for the detailed response. Can you suggest a fitting/adaptor for putting compressed air into the cylinders? I guess I'd need something with a shrader valve that would thread into the injector hole. If I had an old injector, I could braze that up. Is there on off the shelf solution?

Thanks-
Reply With Quote
  #8  
Old 06-05-2018, 10:35 AM
vwnate1's Avatar
Diesel Dandy
 
Join Date: Nov 2005
Location: Sunny So. Cal. !
Posts: 7,717
I've used the Harbor Freight leak down tester to good effect....

Is was about $50 IIRC .
__________________
-Nate
1982 240D 408,XXX miles
Ignorance is the mother of suspicion and fear is the father

I did then what I knew how to do ~ now that I know better I do better
Reply With Quote
  #9  
Old 06-05-2018, 10:37 AM
Registered User
 
Join Date: Jan 2012
Posts: 7,534
Your are welcome.

A compression tester adapter ( injector or glow plug mount ) works fine if you remove the check valve ( usually a tire type valve with a very light spring ). You do not need a dual gauge leak down tester.

Remove the radiator cap, fill rad to top as this helps ID a leak.

Turn the engine so both valves are closed / piston at top then pump in 90 or so PSI air. It may take a few times to get the engine exactly at top and the air might rotate the engine so give it a puff of air first. Stay clear of the ran and belts.

Let the air run for 10 - 15 seconds then look for bubbles in the rad or a rising level of water. Be careful, a very bad gasket / head will result is a spray of water from the rad.
Reply With Quote
  #10  
Old 06-05-2018, 03:20 PM
moon161's Avatar
Formerly of Car Hell
 
Join Date: Mar 2008
Location: Buffalo NY
Posts: 2,057
The HF leakdown tester only has spark plug adapters. It'll work but observe pressure limits & use instructions included to the letter.

The HF diesel compression tester has injector or GP adapters that'll work if you remove the schrader valves. If you go to a hose shop, you can probably get the adapter(s) you need to plumb the injector or GP adapter to a quick connect or schrader inlet.
__________________
CC: NSA

All things are burning, know this and be released.

82 Benz 240 D, Kuan Yin
12 Ford Escape 4wd

You're four times
It's hard to
more likely to
concentrate on
have an accident
two things
when you're on
at the same time.
a cell phone.


www.kiva.org It's not like there's anything wrong with feeling good, is there?
Reply With Quote
  #11  
Old 06-10-2018, 12:11 PM
Registered User
 
Join Date: Dec 2015
Posts: 102
Here is an update on this thread.

I did a lot of research on head gasket sealing potions. There seems to be 3 types.

First, there is the Barrs sealer type which has copper flakes in it. The idea is that the copper flakes get lodged into the leaks in the gasket. It gets hot there and they melt and stay put. I have two friends who used this in Subarus with head gasket leaks, and they reported 100% success.

Second, there is the Sodium Silicate (aka waterglass) type (Steel Seal, Bears Leak, others). This stuff apparently cures at a specific temperature.

Third is the type made by Titan Sealers (actually, they claim to be the only maker of this type). It is a polymer that is designed to cure at a temperature that is high enough that it only occurs at the head.

I decided to try the Titan sealer stuff.

I drained the radiator and block, removed the thermostat, and bypassed the heater core with a piece of copper pipe. I put in the titan seal goop and filled with water. I did 3 run cycles of 20 min idle, 20 min rest, then overnight cool. The next day I took it for a drive, and amazingly, no overheating.

I'll continue several test drives like this before putting the stat back in and reconnecting the heater core, then draining and filling with anti-freeze.

So- not totally out of the woods yet, but it is looking good so far. How long will it last? Who knows. But I do know that I do not have the time to do a head gasket on this car.
Reply With Quote
  #12  
Old 06-10-2018, 12:32 PM
Registered User
 
Join Date: Mar 2009
Location: San Diego
Posts: 3,537
All sealants works on the principal of plugging the leak when the material in the coolant is heated by the combustion gases. The material solidifies and viola, it plugs the leak. I used Blue Devil which is silicon sulphate. It turns into glass when heated. It works for 20k miles on one of my sdl which is pretty good, all things considered. It is definitely not 'permanent' but a good salesman tool to sell the car. If you are selling the car then it is good to go. If you are keeping it then it buys you some time but borrowed time. May be 1 year or so. The other thing is to NOT pressuring the radiator if you think the car is ok. My experience is that pressuring the radiator may dislodge the plugging material. Good luck.

__________________
Not MBZ nor A/C trained professional but a die-hard DIY and green engineer. Use the info at your own peril. Picked up 2 Infractions because of disagreements. NOW reversed.

W124 Keyless remote, PM for details. http://www.peachparts.com/shopforum/mercedes-used-parts-sale-wanted/334620-fs-w124-chasis-keyless-remote-%2450-shipped.html

1 X 2006 CDI
1 x 87 300SDL
1 x 87 300D
1 x 87 300TDT wagon
1 x 83 300D
1 x 84 190D ( 5 sp ) - All R134 converted + keyless entry.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 11:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page