PeachParts Mercedes-Benz Forum

PeachParts Mercedes-Benz Forum (http://www.peachparts.com/shopforum/index.php)
-   Tech Help (http://www.peachparts.com/shopforum/forumdisplay.php?f=1)
-   -   Hard starting and rough running 1991 500sl w129 (http://www.peachparts.com/shopforum/showthread.php?t=191789)

devincie 06-19-2007 09:50 PM

Hard starting and rough running 1991 500sl w129
 
I was hoping someone here could help. I've had my car in the shop for the last three weeks (waiting for parts and diag), and the mechanic cannot find the problem.

Symptoms:

Vehicle hard to start, at all times except up to 15-20 minutes after its driven, and first thing in the morning.

running very rich, spark plugs are black, all of them, black soot on pavement from exhaust pipe.

running rough, it does not matter weather the car is warmed up or not, but it seems to get worse if its hot.

items replaced:
spark plugs, wires, distributor and caps. fuel pressure regulator, EHA valve(was leaking) coolant temperature sensor.

There is no codes in the system, apparently they tried adjusting the fuel pressure (hex key connector on the fuel distributor), this did help the power a bit, but still no luck with the starting problem, and the miss is still there...

Any help would be greatly appreciated.

saumil 06-19-2007 11:45 PM

Cold start valve ? Check the actuator resistance, it should be low, between 10 and 30 ohms. When trying to start, the voltage on the actuator should bearound 10V. If you remove the start valve and try to start the engine, the valve should spray gas. If voltage and resistance are o.k. and the gas does not spray, replace cold start valve.

Is the black smoke occuring after repeated attempts to start. Because this may mean that you are accumulating gas and may actually point to something other than the cold start valve.

Could also be the crankshaft position sensor. But this means you will not have spark on any of the spark plugs. Can be checked with a simple and inexpensive spark tester from local auto store.

Playing with the fuel distributor can cause a whole lot of problems, hopefully it is not there.

david s poole 06-20-2007 10:14 AM

i think it's the fuel distributor sending unequal amounts of fuel and leaking down when engine off.

devincie 06-20-2007 09:46 PM

I've checked the cold start injector, the resistance is almost 20,000 ohms, voltage at plug is just over 10volts, when the injector is removed, and the engine is cranks, there is no fuel coming out of the injector....

just to be sure I loosend the fuel line to the injector, fuel started hissing out, so I have fuel pressure there too.

I will replace this and see what happens, but it looks like we have the culprit.

Thanks for all the hints.

devincie 06-20-2007 09:48 PM

Sorry, I misread the meter, its 20ohms for the resistance.

saumil 06-20-2007 11:00 PM

Yeah, 20K sounds almost like an open circuit, 20 ohms seems reasonable.

devincie 07-12-2007 09:54 AM

New sumptoms!!!
 
Well here is the update, the vehicle in now hard to start at all times, I have replaced the cold start injector with no success.

The idle is still rough on low rpm, and you can actually smell the rich fuel. I pulled the spark plugs out again, and I seel wetness on #2, #7, and #8. Now, the injectors are pretty cheap, but this is what I don't understand, they have no electical solenoid, so I assume the injewctor acts like a nozzle, and it does not stop or control fuel flow, so we are lead somewhere else.

I wilsh I could finally drive this car, it has been sitting almost idle for three months now, any help would be appreciateed.

david s poole 07-12-2007 10:08 AM

how many miles on this car? based on the above posts i still think this is a fuel distributor problem.have you tried leaning down the mixture with a 3mm between the plate and fuel distrib?

saumil 07-12-2007 11:42 AM

I agree with David, now that your cold start appears to be working you have too much fuel during startup. Because it was not working in the past, the fuel mixture might have been enrichened by the fuel mixture adjustment. Lean the fuel mixture and you may succeed.

devincie 07-12-2007 12:53 PM

The car has 99,000 miles. I will try to lean out the mixture, and I assume if that doesn't work, I'm looking at replacing the disributor..... That sounds like big money... Are those things servicable?

Thanks for all your input.

Greg

david s poole 07-12-2007 12:55 PM

used to be now less than$500 exchange.

saumil 07-12-2007 04:27 PM

A rough test can be performed for fuel distributor operation. Disconnect the metal hoses coming out of the distributor (may need to loosen the injector side as well). Car is off for this test. Remove the fuel pump relay and short terminals 7 and 8 of the socket (this starts the fuel pump). On the relay the corresponding pin numbers are 30 and 87. When the air sensor plate is all the way to top, no fuel should come out from any of the outputs of the distributor. Now as you gradually depress the plate, equal amounts of fuel should come out from all the outputs. if any of these two does not happen, need to replace the distributor.

There are other more elaborate tests described in the manual, but they need special tools and the documents are large so I cannot post them here, need to send me an email at saumil@swbell.net if you dont have the manual and need the documents.

saumil 07-12-2007 04:29 PM

By the way, I forgot to mention, whatever I said works for my 87, 260E and I am assuming the parts.operations are similar in your car.

devincie 07-13-2007 06:57 PM

Thanks guys, it looks like I was a victim of multiple issues piled on top of each other. Every part I change makes a bit of a difference and changes the symptoms, I leaned out the mixture to a bit, hesitation at low rpm is almost gone, idle much better, leaned it out some more, no difference, and still the car takes a long time to start. We had a really hot day here today, and it took twice as long as usuall to start. I will perform the test that Saumil describes was the fuel distributor this weekend, and report the results. Thanks again. Greg.

saumil 07-13-2007 11:30 PM

I noticed that you have replaced the EHA, have you tested if the current is flowing thru it ? When the switch is set to run (right before start), 10 - 20 ma current should flow thru the EHA. The current will drop at idle. But if you blip the gas pedal, you should get currents larger than 15ma for each blip. Do this test when the engine is cold. Also, the current measurements must be made via a series circuit with the EHA (not parallel like voltage measurements).


All times are GMT -4. The time now is 06:44 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website