Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 03-09-2000, 02:34 PM
John H's Avatar
Registered User
 
Join Date: Mar 1999
Location: SF Bay Area, CA
Posts: 57
Help!!

I noticed a rough idle on my '86 300E two weeks ago. It also has a noticable hesitation when taking off from a dead stop. Only happens when the motor is warm. Purr's like a kitten when cold. Now for the worse part, gas mileage has gone in the sewer just as prices hit $2+/gal. Was 20 MPG now its 12MPG.

I'm not a FI expert but my first thought is the temp sensor for the fuel enrichment. Anybody else have any thoughts on where to start? I do have the manuals and a good set of tools.

Thanks!

Reply With Quote
  #2  
Old 03-09-2000, 09:07 PM
Registered User
 
Join Date: Mar 1999
Location: Suwanee, GA, USA
Posts: 4,712
It could be that or an oxygen sensor...You need a lambda meter to see if it is online and in closed loop. This is where you get better fuel economy.

------------------
Benzmac:
1981 280GE SWB
1987 16V
ASE CERTIFIED MASTER AUTO TECHNICIAN
SERVICE MANAGER FOR 14 BAY FACILITY
MERCEDES SPECIALIST 8 YRS
PARTNER IN MERCEDESSHOP.COM


Reply With Quote
  #3  
Old 03-10-2000, 09:30 AM
John H's Avatar
Registered User
 
Join Date: Mar 1999
Location: SF Bay Area, CA
Posts: 57
Thanks Benzmac!

I checked the temp sensor and it works beautifully. I don't have a lamba meter. I think I'll just toss a new oxygen sensor in it since the shop charge to check it would be about half the cost of the part.
Reply With Quote
  #4  
Old 03-10-2000, 11:58 PM
Moderator
 
Join Date: Mar 2000
Location: Gainesville FL
Posts: 6,844
A good multimeter tells all on the 86 300e. The fault memory (only active no stored codes on 86-87) is read on pin #3 of the diagnostic socket. Set your meter on duty-cycle and read the value. If you have closed-loop oxygen sensor control you will have a roving duty-cycle; lean and rich about 50% if all is adjusted properly.

If you get a constant duty-cycle it will indicate a given problem 10%, 20%, 30%, etc.
Email if you need a code chart.

To guarantee proper meter set-up. Turn key on, engine off, and you should read 70% on a Federal version car and 85% on a CA version.

If you really want to watch the whole system use your amp-meter section and hook in series to read the EHA current. The EHA (electro-hydraulic actuator) is the mechanical result of all the electronic sensing. It is a controlled leak to the upper chamber pressure of the fuel distributtor.

The amp readings will be in the -60 to +100ma range. There will be a 40+ma current for starting enrichment, 20-30 for cold enrichment, maybe 10ma for acceleration enrichment AND about 10+ and 10- milliamps of O2 sensor correction.

Once warm the value of the current flow would be 0.0ma if the O2 sensor was disconnected. When hooked up the closed loop control should have the milliamp value hovering plus or minus one or two milliamps. If it ranges from -6 to -3 and back the system would be in closed loop but too rich so the mixture is being leaned out (-ma = too rich +ma = too lean.

The relative value of your oxygen sensor can be judged by the rate of the lean/rich correction during these cycles. The sensor should be hot and the engine speed at 2000rpm long enough to stabilize.

------------------


[This message has been edited by Webmaster (edited 03-14-2000).]
Reply With Quote
  #5  
Old 03-14-2000, 12:49 AM
John H's Avatar
Registered User
 
Join Date: Mar 1999
Location: SF Bay Area, CA
Posts: 57
Steve

Great response. Maybe MercedesShop needs another hired gun. It's evening now so I will hook up the meter tomorrow.

I can tell you that the problem did disapear today for a while. Is that possible for a failing O2 sensor? I wish I could say the problem vanished because I fiddled with something but all I did was wash it this weekend (LOL).

Lee, still waiting for the the O2 quote.

Reply With Quote
  #6  
Old 03-16-2000, 11:37 PM
John H's Avatar
Registered User
 
Join Date: Mar 1999
Location: SF Bay Area, CA
Posts: 57
Swaped out the O2 sensor today. The old unit would rattle when shook. The idle hesitation is gone. Looks like that was it. Many, many, thanks Benzmac and Stevebfl!!!!!!!

Can't wait to see if the milage is back up to twenty MPG (if not I'm going to start driving my 6 MPG 428CJ Fairlane convertible around because it's a lot more fun - at least in a straight line).

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
300E 5 speed gas mileage? joshhol Tech Help 25 03-12-2004 02:03 PM
Gas mileage on w126 Jerry Hudson Tech Help 17 10-19-2002 04:15 PM
'86 300E bad BAD traction problem! d2bernhard Tech Help 10 09-04-2002 04:24 PM
Rich Fuel Mixture, Poor Fuel Mileage - after front end collision - '90 300E Wayne Lindholm Tech Help 1 12-05-2001 10:19 AM
Gas Mileage of 300E chc Mercedes-Benz Performance Paddock 4 05-16-2001 11:15 PM



All times are GMT -4. The time now is 02:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page