Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Vintage Mercedes Forum

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 03-07-2008, 07:32 PM
Registered Loser
 
Join Date: Nov 2004
Location: the great northwest
Posts: 257
RUST on LOBES , LOCKED motor?

bought another euro sedan yesterday for next to nothin'.
it had been sittin' for 4 years, owner said because the Solex 4A1 carb had been giving him trouble. (imagine that ) he said the motor was solid.

towed it home and drained the gas. put a battery in it, and it just won't turn over. starter engages, but no go. tried it by hand by the crankshaft, and it's TIGHT.

the oil on the dipstick looks good.
the coolant looks good.
i pulled the valve cover, and the 1st picture will show you what i saw: rust and crud on camshaft/lobes.
then i pulled the plugs, and the 2nd picture will show you what i saw: little rust and (mold?) on the tips. (plug in worst condition in focus in photo).

would you assume the motor's totally seized + wasted, or ?
what would you do now if you were me?

Attached Thumbnails
RUST on LOBES , LOCKED motor?-camshaft.jpg   RUST on LOBES , LOCKED motor?-plugs.jpg  
__________________
-lee
'83 300CDT (286k)

former proud owner of:
'85 mercedes euro 300TD
'80 mercedes 300TD
'77 mercedes 280e
'80 mercedes euro 250
'82 mercedes euro 250

Last edited by blankenship; 03-07-2008 at 07:48 PM.
Reply With Quote
  #2  
Old 03-07-2008, 07:56 PM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 38,613
I would think the cam is toast. It also could be siezed. will the crank wiggle at all? The rust on the plugs is discouraging too. It suggests water has been in the oil to me. Also suggests the cylinders may be very rusty too.

But a good soaking might loosten the pistons enough to get it to turn over, you never know.

But I am thinking very likely it will have to be torn down and gone through.

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #3  
Old 03-07-2008, 07:59 PM
Registered User
 
Join Date: Jan 2008
Location: Redondo Beach, CA
Posts: 188
I would remove the hood, then the head ....and plant flowers in the cylinders

Seriously, is all that rust from sitting in the damp NW climate? I agree that the motor is probably toast.
__________________
1993 190E 2.6 135k
1989 Ford Thunderbird SC 5 Spd 79K
Reply With Quote
  #4  
Old 03-07-2008, 08:49 PM
Registered Loser
 
Join Date: Nov 2004
Location: the great northwest
Posts: 257
crank will wiggle a bit, and seemed to have turned with the starter a little before first 'seizing.' i was tempted to turn i backwards a little by the crank, but didn't.

certainly can't see water in the oil, from dipstick tube...course, i know that doesn't mean much.

as far as "a good soaking," how would one go about that?

i could do a soaking, then try to turn her over without any plugs in her...
maybe do an oil change first?
__________________
-lee
'83 300CDT (286k)

former proud owner of:
'85 mercedes euro 300TD
'80 mercedes 300TD
'77 mercedes 280e
'80 mercedes euro 250
'82 mercedes euro 250
Reply With Quote
  #5  
Old 03-07-2008, 08:51 PM
Glowplug's Avatar
Registered User
 
Join Date: Mar 2008
Location: Tulsa, OK
Posts: 71
I've seen some crazy redneck stuff around here with guys firing motors (chevrolet) that have been sitting with no hoods and rust throughout various components.

Motors i never thought would fire, turn right over .


If you can actually turn the crankshaft via the bolt then i would say it isn't "seized" . If the motor oil looks milky than you might have water in the oil .


If the crank turns, then i would say to pull the head and replace cam, get new plugs and try it again .
__________________
93 300 D 2.5 turbo
Reply With Quote
  #6  
Old 03-07-2008, 08:57 PM
Registered User
 
Join Date: Jan 2008
Location: Redondo Beach, CA
Posts: 188
For a "good soak", try putting some diesel in through the spark plug holes, let it sit for a day or so,with the plugs in loosely, then squirt in a bit of motor oil, and see if you can turn the crank pulley.
__________________
1993 190E 2.6 135k
1989 Ford Thunderbird SC 5 Spd 79K
Reply With Quote
  #7  
Old 03-07-2008, 09:06 PM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 38,613
I think the cam may be siezed. this is tricky since it turns in unfaced aluminum. I would proceed with care about the cam. I would probably pull the cam and towers and try to free the journals one at a time.

As for the cylinders various things will help. Tranny fluid, marvel mystery oil, penetrating oil as well or better than diesel fuel. just be sure to remove plugs before trying to turn it over so the oil can be pushed out.

I would drain the motor oil and see if there is water in the bottom of the pan, probably first thing.

Good luck

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #8  
Old 03-07-2008, 09:19 PM
Registered Loser
 
Join Date: Nov 2004
Location: the great northwest
Posts: 257
plan

good to have a plan, thanks.

can i really spray penetrant into the spark plug holes? (seems like that would the the most powerful way to get things loosened up, but, is it also possible it'll be detrimental in some other way (as opposed to marvel mystery, or the like)?

maybe i should spray down the cam journals with penatrant before i try moving them?
__________________
-lee
'83 300CDT (286k)

former proud owner of:
'85 mercedes euro 300TD
'80 mercedes 300TD
'77 mercedes 280e
'80 mercedes euro 250
'82 mercedes euro 250
Reply With Quote
  #9  
Old 03-07-2008, 09:39 PM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 38,613
penetrating oil will cause no problems, its just expensive.

Its a good chance you'll wind up tearing it down but if you should happen to be successful it might run.

But I would pull the pan and clean it out good before trying to run it.

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #10  
Old 03-08-2008, 10:21 AM
Registered Loser
 
Join Date: Nov 2004
Location: the great northwest
Posts: 257
well then

i think i'll:

1. drain the oil + check for water.
2. spray a couple courses of penetrant down the spark plug holes.
3. spray penetrant on the cam journeys and remove them + towers.
4. rub journeys with scotchbrite pad, and, if not absolutely toast, replace.
5. top up plug holes w/ marvel mystery
6. start the dang car!

how's that sound?
__________________
-lee
'83 300CDT (286k)

former proud owner of:
'85 mercedes euro 300TD
'80 mercedes 300TD
'77 mercedes 280e
'80 mercedes euro 250
'82 mercedes euro 250
Reply With Quote
  #11  
Old 03-08-2008, 10:31 AM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 38,613
Its a plan. Just remember to allow the oil to be pushed out before installing plugs.

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #12  
Old 03-08-2008, 10:34 AM
Registered User
 
Join Date: Mar 2006
Location: Australia
Posts: 115
1. Soak liberally with gasoline (petrol).
2. Light a match.
3. Stand well clear.
Reply With Quote
  #13  
Old 03-08-2008, 02:20 PM
Registered Loser
 
Join Date: Nov 2004
Location: the great northwest
Posts: 257
Red face REVISED plan?

drained the oil. see the photos for what it looked like. second photo shows a drip of the newly drained oil (left) next to a drip of some other old oil i had sittin' around from another car. big difference.

shined a flashlight down the spark plug holes. i could see (in the #2 and #5 cylinders) some watery lookin' stuff down in there. sucked out a couple ounces of it with my mightyvac. it's like dirty water with little rusty tinge to it.

does this mean i'm sunk?
how'd that water get in there? did the guy blow a head gasket and withhold that information? or does water sneak into the system when stored, and condense in the head?

what now? i assume i shouldn't try and start her knowin' that crud's in there. maybe i should pull the head? or stick to the original plan?
Attached Thumbnails
RUST on LOBES , LOCKED motor?-oil.jpg   RUST on LOBES , LOCKED motor?-oil-compare.jpg  
__________________
-lee
'83 300CDT (286k)

former proud owner of:
'85 mercedes euro 300TD
'80 mercedes 300TD
'77 mercedes 280e
'80 mercedes euro 250
'82 mercedes euro 250
Reply With Quote
  #14  
Old 03-08-2008, 03:34 PM
Tomguy's Avatar
Vintage Moderator
 
Join Date: Aug 2002
Location: near Scranton, PA
Posts: 5,407
From the pic of the camshaft, it's quite clear what happened:

The valve cover was left off the engine. I've seen MB engines with their valve covers left off in the junkyard - they all look like that. Not a single one I've ever seen in the junkyard that had the valve cover on was rusted - even if the cam was dry (no oil) and the hood was open.

The oil wasn't oil. I would consider the engine inside of that not worth rebuilding. If you get into tearing it down you'll wind up wanting to rebuild, rework or replace most everything. At this point, you're best off trying to take the heaviest rust off of the camshaft (with 0000 steel wool most likely), putting penetrant into the cylinders (PB Blaster) and letting that soak, and repeatedly putting penetrant into the cyls every 4 hours - a 5 second shot. Do that over the course of about 2-3 days, then put a breaker bar on the crank bolt and gently turn the engine the SLIGHTEST bit backwards, then pull forwards until it seems to spin freely. If it seizes again, repeat the PB Blaster process. You'll eventually get it to turn freely, then you want to replace the oil filter and fill the crankcase with 1/2 the cheapest 5w30 and 1/2 the cheapest ATF and attempt to crank it with the starter. Do that until it builds up oil pressure. If you're feeling daring, try to start it off of ether or hell, even gas and try running it for about 2-3 minutes. Then shut it off, check the oil and if watery, drain and re-fill with 5w30 and repeat.

If you can get it to run, then you resurrected an engine that you don't want to consider rebuilding. Congrats! Drive it until it dies.
__________________
Current:
2021 Charger Scat Pack Widebody "Sinabee"
2018 Durango R/T

Previous:
1972 280SE 4.5
2014 Jeep Grand Cherokee Limited "Hefe", 1992 Jeep Cherokee Laredo "Jeepy", 2006 Charger R/T "Hemi"
1999 Chrysler 300M - RIP @ 221k
Reply With Quote
  #15  
Old 03-08-2008, 04:02 PM
Hatterasguy's Avatar
Zero
 
Join Date: Nov 2002
Location: Milford, CT
Posts: 19,318
Tomguy nailed it, thats what I would do.

Get a rebuild, or junkyard engine.

__________________
1999 SL500
1969 280SE
2023 Ram 1500
2007 Tiara 3200
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 09:20 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page