Hello again...

I apologize if I sound mad or anytihing like that; I'm very frustrated at the moment.

This is on my '85 300D...as I've mentioned in one or two other threads, my instrument lights are dead. This isn't just the lights on the instrument panel; the ACC lights, the window switch lights, the hazard switch backlighting, and the "upper switch panel" (with the antenna, rear window, sunroof, and rear defogger switches) lights...basically every interior light that's supposed to come on with the headlights, except for the gear indicator light, is dead.

I've tried bypassing the rheostat to no avail. From the rheostat terminals, I've got 12 volts AND 0 ohms to ground, implying that the circuit's complete. But, no lights, and I don't have power at the light sockets at the ACC panel or at the window switches.

The fuse checks out okay, and everything else on that fuse works properly.

Does anyone have any suggestions? I'm getting desperate here...

This started when I jury-rigged the center-console window switches in order to raise one window when its switch failed. I've since re-wired the switches the way they're supposed to be (with a replacement passenger's side window switch assembly; thanks again mattdave!), thinking that I had messed the lights up somehow and cut a daisy-chain ground when I did the jury-rigging, but re-wiring things so they were "right" didn't do any good (at least all my window switches work now )

Thank you for any thoughts on the matter...I'm starting to wonder where my matchbook is...

__________________
2001 VW Jetta TDI, 5 speed, daily driver
1991 Ford F-350, work in progress
1984 Ford F-250 4x4, 6.9l turbo diesel, 5 speed manual
Previous oilburners: 1980 IH Scout, 1984 E-350, 1985 M-B 300D, 1979 M-B 300SD, 1983 M-B 300D
Spark-free since 1999

Electrical problems are very difficult to diagnose over the net, that said the first thing I would check are the traces on the circuit board. After nearly pulling out what hair I have left, I found a bad trace on my '85, after soldering a wire from point to point got all the lights back and a functioning dimmer. Just check continuity on each trace, if you have trouble seeing them hold the board up to a light. If need be I can pull my cluster and post a picture of which trace and repair-- Good Luck, James

James, would that also explain the ACC lights and the window-switch lights not working?

I'll have to check on that...although it'll have to wait for tomorrow. Thanks for the idea

Yes, all the instrument lights go through the same circuit, its been a while but I think the trace may have gone to a Hella relay soldered to the board.
If I get home early enough tomorrow I will pull the cluster and have a look, need to paint the light pockets and freshen the bulbs anyway.
James

Lets look at this carefully, Nah lets just fix it.

This is the list of items coming from Fuse #1 in the fuse box.

Center consol illimination
Lights Park/Tail RH
Lights Marker/license
Warning Indicators/instument cluster illumination
Warning system.

Sound like you

So check to see if all these items are inop.

If so its the #1 fuse, replace it, If still a no-go then its wire harness time.

Wire harness.

The diagram shows from fuse #1 A GY/RD wire goes to the light switch. check voltage at the back of the light switch at the GY/RD wire.

From the light switch GY/VI goes to the warning system relay and the LH/RH license light. Check votage there

The GY/VI wire also goes to the instument cluster for illumination and to the center console upper section. Also the wire goes to the radio and cigar lighter then go ground G102 (Behind center of instrument cluster)

It is this GY/VI wire that goes to the rheostat. So if no power there, then we work back to the fuse. (You have checked for voltage on both sides of the fuse, correct??)

The only thing left besides the wire is the light switch . Use the ohm meter and make sure it is working correctly. You may have burnt out a contact with the switch rigging.

Switch contacts

From the fuse to the switch GY/RD wire to contact N30 (or M30 hard to read) The output ( the GY/GY/VI wire, as the manual shows it) is contact K. so check continuity with the switch ON from N30 to K.

http://skinnerbox.steaky.org/Service/W123/w123CD2/Program/ETM/123%20turbodiesel_2.pdf


page 121/4/5 and is the complete diagram for your problem.


Dave

To add, the wire does continue to the window switches from the instrument panel to the switches as a GY/BU wire to the C124 distribution block then as a GY wire to the switches. So there is a connection between the switch rigging you did and the circuit.

__________________
1970 220D, owned 1980-1990
1980 240D, owned 1990-1992
1982 300TD, owned 1992-1993
1986 300SDL, owned 1993-2004
1999 E300, owned 1999-2003
1982 300TD, 213,880mi, owned since Nov 18, 1991- Aug 4, 2010 SOLD
1988 560SL, 100,000mi, owned since 1995
1965 Mustang Fastback Mileage Unknown(My sons)
1983 240D, 176,000mi (My daughers) owned since 2004
2007 Honda Accord EX-L I4 auto, the new daily driver
1985 300D 264,000mi Son's new daily driver.(sold)
2008 Hyundai Tiberon. Daughters new car

...and my car is no longer condemned!! For the moment, at least.

James, you were right...found a break in the board right after the far side of the rheostat terminal. Soldered that (only had a gun, so it's ugly...but it works and didn't compromise anything else...I hope), and the lights all work now.

Now, while the instrument cluster's in many pieces, I get to renew everything I can, clean up, etc...guess it's time to bypass the rheostat (even though it was okay). Also, has anyone tried replacing the dash bulbs with LED's?

Thanks again

Excelent!! glad it worked out and you could save the matches for another day As to the led, the only ones I have seen have forward ilumination, so I dont think they would help. gonna try the white paint trick and fresh bulbs myself.
Good Luck, James