Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-26-2008, 07:44 AM
mobenz's Avatar
Registered User
 
Join Date: Sep 2006
Location: SW Missouri
Posts: 103
How to test the glow plug relay

I guess I need to check the glow plug relay in my 1978 300CD. I have a volt/ohm meter, but I don't know that much about using them. Any help is appreciated.

__________________
"If we can't have fun while we're here, we might as well go to the house".

1978 300CD
1985 300TD
1999 Land Rover Discovery II
rover1@sbcglobal.net
Reply With Quote
  #2  
Old 07-26-2008, 08:36 AM
777funk's Avatar
Registered User
 
Join Date: Dec 2006
Posts: 1,031
Quote:
Originally Posted by mobenz View Post
I guess I need to check the glow plug relay in my 1978 300CD. I have a volt/ohm meter, but I don't know that much about using them. Any help is appreciated.
It's not super hard. It's a w123 so I think it's the same as my old 300d but I could be wrong. Anyways, probably the same concept.

The goal of this part (the GP Relay) is to be the brain for your glow plug circuit. They need to be on for 20-30 seconds before you start the engine and turn off after it's started (exception the after glow upgrade for the newer MB diesels). I believe if you don't turn the key to start, the GPs will remain on for 1 minute.

To do this it's got a 5 wire harness with somewhat large wire (maybe 12AWG) going to the GPs. You can either pop the top off of this harness to expose the pins (Look at the wire harness and you'll see it has a snap lid on the back side of it) and measure on one of the 5 pins while it's plugged in to the GP relay or measure at the GP terminal itself.

What you're looking for is 12V at the GP cycle (first minute I believe after turning the key). Measure with a voltmeter (multimeter set to measure at least 12V). Put the black on the battery ground and the red on the battery Red just to check and make sure you're measuring 12V. Then have someone turn the key to Glow and measure at the GP relay's 5 pins or the Glow plugs themselves. If you have loop (series) style glow plugs your circuit will be a little different. If so you should measure voltage across the two wires on the GP but it won't be 12V. Rather 12V divided by the number of GPs in series.

Now if you don't measure voltage at the GPs, don't blame the relay yet--- here's why:

1. The relay is designed to NOT provide the GPs with power if more than 2 are burned out. (measure ohms across the GP -with it out of circuit- and you should see .7ohms approx on the new style (not old series type-if it is series type you'll see still close to this and Open Circuit still equals dead GP). If it's an Open Circuit or very high resistance, the GP is dead... you can also just use jumper cables on the GP and see if you get a red glow if it's not the series style GPs)

2. The connections on the relay may not be tight. Check them.

3. The connections at the GPs may be shorted or not in contact. Check them.

4. The FUSE on the GP relay may be shot. It's a big 80A (I think) silver colored strip fuse (about 1 1/4" by 1/4") that has a screw on either side. Measure across this to make sure it's good. You should see 12V on either side of the fuse or you can measure OHMS across it and see close to '0' ohms.

5. The wires could be shot. But this I'd doubt. Again though you can measure across them with an ohm meter and should get close to ZERO ohms.

But that should help you.

Here's more of a description of how your GP relay works if you're board:

It has some simple logic inside that does the following:

-Is the key turned to Glow?
-Do I measure a resistance that says I've got all but at least 1 or 2 glow plugs still working? (my guess as to how it knows the GPs are still good is by resistance)
-Has the starter engaged (the purple wire on the 4 wire harness senses the starter's voltage signal when it's energized)
-If YES to the first TWO and NO to the THIRD question, send 12V to the glow plugs for 1 minute.

I've fixed GP relays with corroded Relay copper terminals. All you need is a screwdriver to take the relay apart and sandpaper to scuff the terminals clean.

Anyways, hope this helps.
Nick
__________________
-E300d '99 350k
-Suburban '93 220k
-TDI Jetta '03 350k
Sold
-F250 '96 7.3
-Dodge Ram 12V
-E320 '95 200k
-E320 Wagon 1994 155k
-300d Turbo '87 187k miles
-E320 1994 200k
-300d Turbo '84 245k (sold to Dan62)
-300d Turbo '84 180k
-300sd '80 300k
-7.3 Powerstroke Diesel 15P Van 500k+ miles
-190d '89 Non Turbo 2.5 5cyl 240k (my first MB)
Tom's Imports of Columbia MO Ruined the IP in changing leaky delivery valve O-Rings - Refused to stand behind his work. Mid-MO MB drivers-AVOID Tom's.

Last edited by 777funk; 07-26-2008 at 08:46 AM.
Reply With Quote
  #3  
Old 07-26-2008, 09:00 AM
777funk's Avatar
Registered User
 
Join Date: Dec 2006
Posts: 1,031
Also, there's probably more on here if you dig for it.

Feel free to ask if anything is confusing as well.

Did you just pick up the CD? Not on Craigslist-Springfield was it? I saw a 78 a few weeks back. Those are cool old cars. Any 123 is.
__________________
-E300d '99 350k
-Suburban '93 220k
-TDI Jetta '03 350k
Sold
-F250 '96 7.3
-Dodge Ram 12V
-E320 '95 200k
-E320 Wagon 1994 155k
-300d Turbo '87 187k miles
-E320 1994 200k
-300d Turbo '84 245k (sold to Dan62)
-300d Turbo '84 180k
-300sd '80 300k
-7.3 Powerstroke Diesel 15P Van 500k+ miles
-190d '89 Non Turbo 2.5 5cyl 240k (my first MB)
Tom's Imports of Columbia MO Ruined the IP in changing leaky delivery valve O-Rings - Refused to stand behind his work. Mid-MO MB drivers-AVOID Tom's.
Reply With Quote
  #4  
Old 07-26-2008, 10:29 AM
mobenz's Avatar
Registered User
 
Join Date: Sep 2006
Location: SW Missouri
Posts: 103
Actually, I think the issue is with the ignition switch, which I have already ordered. I have had this car for about 2 years. Just converted to WVO, and then the electrical went south on me. I have been having intermittent starting problems for several months.
__________________
"If we can't have fun while we're here, we might as well go to the house".

1978 300CD
1985 300TD
1999 Land Rover Discovery II
rover1@sbcglobal.net
Reply With Quote
  #5  
Old 07-26-2008, 11:19 AM
Registered User
 
Join Date: Sep 2004
Posts: 8,971
Quote:
Originally Posted by 777funk View Post
Feel free to ask if anything is confusing as well.
What is the basis of your belief that the relay won't close unless some minimum number of glow plugs are "working?"

Why do you believe that the relay opens concurrent with starter engagement?
Reply With Quote
  #6  
Old 07-26-2008, 11:25 AM
777funk's Avatar
Registered User
 
Join Date: Dec 2006
Posts: 1,031
Quote:
Originally Posted by tangofox007 View Post
What is the basis of your belief that the relay won't close unless some minimum number of glow plugs are "working?"

Why do you believe that the relay opens concurrent with starter engagement?
I've seen it in action. Unplug 3 of your glow plugs and turn the key and your GP light won't come on. But I may be wrong about the relay not energizing the GPs. That may be incorrect. I do know the dash light will not illuminate.

As far as the starter engagement shutting off the GPs, that is what the purple wire on the 4 prong harness going to the relay does. It is a signal voltage to the GP relay to shut off.
__________________
-E300d '99 350k
-Suburban '93 220k
-TDI Jetta '03 350k
Sold
-F250 '96 7.3
-Dodge Ram 12V
-E320 '95 200k
-E320 Wagon 1994 155k
-300d Turbo '87 187k miles
-E320 1994 200k
-300d Turbo '84 245k (sold to Dan62)
-300d Turbo '84 180k
-300sd '80 300k
-7.3 Powerstroke Diesel 15P Van 500k+ miles
-190d '89 Non Turbo 2.5 5cyl 240k (my first MB)
Tom's Imports of Columbia MO Ruined the IP in changing leaky delivery valve O-Rings - Refused to stand behind his work. Mid-MO MB drivers-AVOID Tom's.
Reply With Quote
  #7  
Old 07-26-2008, 11:43 AM
Diesel911's Avatar
Registered User
 
Join Date: Sep 2007
Location: Long Beach,CA
Posts: 51,038
Do you have the older style loop type glow plugs (big and have zig-zag wires connecting them) or pencile type glow plugs?
My understanding is that if you hava the loop style Glow Plugs that they are wired in series and if one goes bad the rest will not work.
Is your Glow Plug Relay under the hood on the fender well or under the dash board behind the instrument cluster?
Here is a site that might help:
http://www.pauldrayton.com/uploadfiles/merc/Service/W123/Index/617N/15EngineElec.html
__________________
84 300D, 82 Volvo 244Gl Diesel
Reply With Quote
  #8  
Old 07-26-2008, 11:46 AM
Registered User
 
Join Date: Sep 2004
Posts: 8,971
Quote:
Originally Posted by 777funk View Post
I've seen it in action. Unplug 3 of your glow plugs and turn the key and your GP light won't come on. But I may be wrong about the relay not energizing the GPs. That may be incorrect. I do know the dash light will not illuminate.
Seeing the light in action is not the same as seeing the relay in action. The operation of the light and the operation of the relay are two different concepts. You unplug three of your GP's and see if your relay doesn't still work, even when the light doesn't.

Quote:
Originally Posted by 777funk View Post
As far as the starter engagement shutting off the GPs, that is what the purple wire on the 4 prong harness going to the relay does. It is a signal voltage to the GP relay to shut off.
There are two "signals" transmitted by the purple wire. One that the key has been placed in the start position and one when the key is released from the start position. It's the latter that terminates the glow cycle. (Whether the starter actually "engages" is irrelevant.)

Note: These observations might not be relevant to the original question, depending on the type glow timer installed on the subject vehicle.

Last edited by tangofox007; 07-26-2008 at 11:51 AM.
Reply With Quote
  #9  
Old 07-26-2008, 12:55 PM
Diesel911's Avatar
Registered User
 
Join Date: Sep 2007
Location: Long Beach,CA
Posts: 51,038
When I went to an auto parts site and looked up the glow plugs for his year and model it showed the older Loop style plugs or those big pencile type conversion Glow Plugs.

If his Glow Plug relay is a silver metal box behind the Instrument Cluster; I have yet to see a trouble shooting thread on how to trouble shoot that type of relay. (Maybe the members over in the vintage Mercedes part of the forum know more about this relah.)

If it has the under the hood fender wall one the trouble shooting will be similar to the newer pencile type relays with the exeption that checking the Glow Plugs will be different.
I hope he will tell us what type of plugs/relay he has.
__________________
84 300D, 82 Volvo 244Gl Diesel
Reply With Quote
  #10  
Old 07-26-2008, 06:20 PM
Registered User
 
Join Date: Nov 2007
Location: Central TX
Posts: 9
I can't figure out preglow plug relay problem.

All my notes are in bold. I would sure appreciate any ideas you guys can come up with.


Quote:
Originally Posted by 777funk View Post
To do this it's got a 5 wire harness with somewhat large wire (maybe 12AWG) going to the GPs. You can either pop the top off of this harness to expose the pins (Look at the wire harness and you'll see it has a snap lid on the back side of it) and measure on one of the 5 pins while it's plugged in to the GP relay or measure at the GP terminal itself.

What you're looking for is 12V at the GP cycle (first minute I believe after turning the key). Measure with a voltmeter (multimeter set to measure at least 12V). Put the black on the battery ground and the red on the battery Red just to check and make sure you're measuring 12V. Then have someone turn the key to Glow and measure at the GP relay's 5 pins or the Glow plugs themselves. If you have loop (series) style glow plugs your circuit will be a little different. If so you should measure voltage across the two wires on the GP but it won't be 12V. Rather 12V divided by the number of GPs in series.

I do not get voltage. The diesel is a 190D Year 1987.


Now if you don't measure voltage at the GPs, don't blame the relay yet--- here's why:

1. The relay is designed to NOT provide the GPs with power if more than 2 are burned out. (measure ohms across the GP -with it out of circuit- and you should see .7ohms approx on the new style (not old series type-if it is series type you'll see still close to this and Open Circuit still equals dead GP). If it's an Open Circuit or very high resistance, the GP is dead... you can also just use jumper cables on the GP and see if you get a red glow if it's not the series style GPs)

All my GP's at the wire harness measure about .6 ohms after correcting for the wire leads resistance.

2. The connections on the relay may not be tight. Check them.

The somewhat larger wire that is attached (via a brass bolt) to the preglow relay is showing voltage to the relay and is a good clean conection.

There is no voltage from the 5 pins on the relay after turning the key to the point where the glow plug light should light. The four pin connector does not appear to be real tight. I took a pair of needle nose pliers and made them a bit oblong. This did appear to help
.

Only one of the four pins receives voltage while the key is engaged. Does this sound correct. What do the other three do?

3. The connections at the GPs may be shorted or not in contact. Check them.

This is not indicated by the ohm meter.


4. The FUSE on the GP relay may be shot. It's a big 80A (I think) silver colored strip fuse (about 1 1/4" by 1/4") that has a screw on either side. Measure across this to make sure it's good. You should see 12V on either side of the fuse or you can measure OHMS across it and see close to '0' ohms.

Checks out fine.

5. The wires could be shot. But this I'd doubt. Again though you can measure across them with an ohm meter and should get close to ZERO ohms.

But that should help you.

Here's more of a description of how your GP relay works if you're board:

It has some simple logic inside that does the following:

-Is the key turned to Glow?

Yes
-Do I measure a resistance that says I've got all but at least 1 or 2 glow plugs still working? (my guess as to how it knows the GPs are still good is by resistance)

All check out fine.

-Has the starter engaged (the purple wire on the 4 wire harness senses the starter's voltage signal when it's energized)

This must be the one I am receiving voltage from.

-If YES to the first TWO and NO to the THIRD question, send 12V to the glow plugs for 1 minute.

What do you mean by this? Unplug the harness and send 12 volts to the corresponding pin.

I've fixed GP relays with corroded Relay copper terminals. All you need is a screwdriver to take the relay apart and sandpaper to scuff the terminals clean.

I did this a couple months ago (after having hard start issues) and cleaned all the terminal points and the everything worked including the glow plug light. Last week the car would not start (B100 does not help). The glow plug light did not light up, not even for a second. I took the relay apart and the one of the 4 contact pins was completely burnt off.

I bought a new preglow relay and installed it thinking it would be an easy fix.

I even think I can feel and hear the relay make contact. Could I have a defective preglow relay even though it is brad new? MB has glued or done something to the relay that prevents me from taking it apart to see what is going on.

What else could it be?
Anyways, hope this helps.
Nick
Reply With Quote
  #11  
Old 07-26-2008, 06:25 PM
Bens lover's Avatar
Benz Whisperer
 
Join Date: Mar 2006
Location: Surfers Paradise,Australia.WHERE THE SHARKS COME OUT TO PLAY! And Vancouver Canada where it rains everyday!
Posts: 650
Thumbs up

Try looking at this site

http://dieselgiant.com/glowplugrepair.htm
__________________
Cheers
Big Dan MEng

Visit my Blog..
http://allformercedesbenz.blogspot.com/

www.benzguy.piczo.com



If at first you don't succeed,
Skydiving is not for you.

ARTIFICIAL INTELLIGENCE IS NO
MATCH FOR NATURAL STUPIDITY.

If anything can go wrong,fix it!
The hell with Murphy!!

I never think of the future.It comes soon enough.
Reply With Quote
  #12  
Old 07-26-2008, 08:45 PM
Registered User
 
Join Date: Nov 2007
Location: Central TX
Posts: 9
Did that.

Great web sight and very helpful. Everything checks out fine except there is no voltage coming from the 5 GP pins. In other words I know it is relay related. The only problem is it's brand new.

I get voltage from the battery to the large gauge wire that is bolted to the relay. The fuse checks our fine, voltage on both sides. Still no voltage to the 5 pins.

What this boils down to is the 4 pin wiring harness doing what it is supposed to do.

The four pins according to my wiring diagram (from a manual I payed way to much for).

Terminal 50 Cranking input. I believe it is from the starter.
Terminal 15 is from the run start input.
Terminal 31 Looks like the ground wire.
Terminal LA I believe this is the pin that sends info back to Pre glow lamp indicator yellow light.

I get a full 12 Plus volts from terminal 15 while the key is in in the position just before you turn over the car.

Terminal 50 provides only 10.5 volts. Could this be the problem? Or is the starter pulling the voltage down?
Reply With Quote
  #13  
Old 07-26-2008, 09:13 PM
Registered User
 
Join Date: Sep 2004
Posts: 8,971
Quote:
Originally Posted by cici235 View Post
Terminal 50 provides only 10.5 volts.
The function of the terminal 50 input is to interrupt the glow cycle following engine start. If the cycle is never starting, the problem is not associated with terminal 50. Sounds like a timer/relay failure to me; sometimes parts are bad right out of the box.

You should be able to hear the relay click closed and then open after 30-40 seconds.

Last edited by tangofox007; 07-26-2008 at 09:20 PM.
Reply With Quote
  #14  
Old 07-26-2008, 09:44 PM
Registered User
 
Join Date: Nov 2007
Location: Central TX
Posts: 9
Quote:
Originally Posted by tangofox007 View Post

You should be able to hear the relay click closed and then open after 30-40 seconds.

Sure glad I saved the old one. Even though one of the contact points is shot it still acts differently than the new one.

Example

The new relay only engages the contacts while the engine is cranking. Once the key is turned off the contacts disengage.

The contact points on the old one (well two of them) make contact as soon as the the key is turned to the glow position.

Al I have to do is hold down the contact points on the old one and voltage is passed to the 5 pins.

Thanks. My luck that I would get a bad relay right out of the box.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 09:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page