|
|
|
#1
|
|||
|
|||
Replacement of the Clear Fuel Lines on Diesel Engines
I had a question with regard to the clear or somewhat opaque fuel lines that are connected from the injection pump to the main fuel filter . They are fastened by banjo fitting. The ones on my 240D and 300SDL are quite brown and you can't see through them any more. Is there a certain time that these lines must be replaced? I've looked through the maintenance manual and don't see any mention of it. Mine are not leaking but being that they are made of plastic I was wondering if they are to be replaced often. Mine appear to be original.
Herb '82 240D '87 300SDL |
#2
|
|||
|
|||
The only time that I've replaced them is when some one broke them.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#3
|
|||
|
|||
Fuel lines?
I noticed the same thing on my 1987 SDL. Posted a question here but didn't get many replies. Was at the local MB dealership and asked about these lines. The parts guy told me that they are only available in a kit along with replacement banjo fittings. He also told me that the fuel line material (the clear plastic) has to be Heat Shrunk in place. That is why there are no clamps on any of the fittings! I've seen alot of different engines both gas and diesel and this was new to me, I can appreciate the value of being able to see fuel in the lines but mine are so dark the fuel can't be seen. Mine seem mighty stiff but maybe that's the way they always where?T hey just don't look "good". I've decided to hold off any replacement for now but I keep some hose and clamps in my possibles box in the trunk. Hey Doc do they break often? Regular? As stiff as mine are I would think they could be broken when your doing some wrenching in the area. Thanks and good luck.
|
#4
|
|||
|
|||
Don't replace unless they are leaking or brittle
Greetings,
I can't see any reason to replace these lines unless they are leaking or causing air to enter your fuel system. The brownish color you see is simply the rubber hose absorbing the elements of the fuel, which is quite raw compared to gasoline. I'd think that less than a years use on new lines would have the same appearance. Charles
__________________
"Tell me and I will listen, Teach me and I will learn, Show me and I will accomplish, Involve me and I will succeed." '84 300SD 256,000 Gold on Brown (Mileage Award) '86 300E 246,000 Blue on Tan |
#5
|
|||
|
|||
I've replaced one of them on my 220D with standard fuel line and a couple clamps. Not worth trying to get the original, as it isn't available anymore as an aftermarket and would have to be special ordered. The 240D parts were, but that was a couple years ago.
They will eventually get brittle and break if moved -- if you need to remove the IP or filter housing, plan on removing them carefully and be prepared to replace them. Peter
__________________
1972 220D ?? miles 1988 300E 200,012 1987 300D Turbo killed 9/25/07, 275,000 miles 1985 Volvo 740 GLE Turobodiesel 218,000 1972 280 SE 4.5 165, 000 - It runs! |
#6
|
|||
|
|||
I would expect them to get brittle over time, due to engine heat. Probably no chance of successfully removing them once they are a few years old. It is nice having the clear lines because air bubbles in the fuel can be very quickly diagnosed.
|
#7
|
|||
|
|||
So then it's safe to say that these plastic lines last the life of the engine unless disturbed? From what I've read, these lines aren't replaced on a regular basis.
I know mine are brittle and if I move them I know they'll break. Herb '82 240D '87 300SDL |
#8
|
|||
|
|||
Ive never had to replace them, but when I do, I'll just buy black rubber hose, or to go with my current theme, stainless steel braided hose for alchohol resistance as I'm burning biodiesel. It just looks purdy!
__________________
Matt 2003 Jetta Wagon TDI 145,000MI 1999.5 Jetta TDI 287,000MI 2001 Suzuki SV650S 26,000MI 2008 Yamaha Vino 125 11,000MI http://www.crazymatt.org |
#9
|
|||
|
|||
Well, it never fails...you go in to do one job and you end up causing yourself to have do do another.
BillyBob, I can say the adage is true, "The clear fuel lines will last a life time unless disturbed." I "disturbed" mine while installing a new primer pump, so now I am trying to order some new ones. The two part numbers I got which included the fittings on each end were 615 070 56 32 and 615 070 40 32. I was told I would also require (8) Seals # 007 603 01 21 11. My local shop will have to order them. I have heard stories of having to soak the ends in boiling water to get them to fit. I'll let you know how it goes.....
__________________
'06 E320 CDI 51K miles '02 VW Jetta GLS TDi 120k miles '99 Ford E350 7.3L Powerstroke 200k miles -sold '84 Euro 300D 5 spd manual 317k miles - sold |
#10
|
||||
|
||||
The last time I was at the nearest "pull a part" place I grabbed a set of these babies - along with the banjo fittings.
__________________
Jim |
#11
|
|||
|
|||
I have a set of these hoses ready to install too on my '82 240D. The sales person at the local MB dealership said nothing about seals. BUt it sounds like I'll have to get some seals then in order to do this right. I was wondering what are the seals made of?
Herb '82 240D '87 300SDL |
#12
|
|||
|
|||
Seals?
What kind of "seals" and where would they go?
|
#13
|
|||
|
|||
Originally the seals for the banjo fittings are aluminum washers (thin and very narrow). You can use aluminum or copper to replace the original seals. Do not over-tighten the banjo fittings.
Good Luck! Tom
__________________
America: Land of the Free! 1977 300D: 300,000+ miles American Honda: Factory Trained Technician & Honor Grad. Formerly: Shop Foreman; Technical Advisor to Am. Honda; Supervisor of Maintenance largest tree care co. in US for offices in Tex. |
#14
|
|||
|
|||
Clear line vs. nipple ends & banjo fittings
Greetings all,
Just to clarify some of the folks out there scratching their heads wondering where there could possibly be seals at on the clear fuel lines. There are no seals on the clear lines but on the banjo fitting there is. As mentioned in a previous post the clear lines are heated in boiling water to cause it to be pliable during installation. Phil at Part Shop can give you the p/n for the clear line by the meter I think it is, but it's not real cheap to buy. Others have resorted to using translucent small diameter water line with clamps, and that one will work as well. I think the line will also respond to heated water, causing it to shrink around the fitting, but cools rapidly so the heat source can't be far from the car. I have this type of line installed on one Benz and it seems to work fine and is resistant to color change more so than the more rubber content MB hoses. Charles
__________________
"Tell me and I will listen, Teach me and I will learn, Show me and I will accomplish, Involve me and I will succeed." '84 300SD 256,000 Gold on Brown (Mileage Award) '86 300E 246,000 Blue on Tan |
#15
|
|||
|
|||
Thanks Tcane for the info.
Is there a certain torque value for these banjo fitting bolts? Herb '82 240D '87 300SDL |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Excellent Diesel Article | Ron Johnstone | Diesel Discussion | 7 | 02-18-2005 03:18 PM |
98 ML320 - Fuel Filter and New Fuel Lines | movpe | ML, GL, G-Wagen, R-Class, Unimog, Sprinter | 2 | 04-10-2004 10:09 PM |
Diesel torque and sound | kerry | Diesel Discussion | 24 | 01-09-2004 05:47 PM |
Tips for Changing Fuel Lines on 1989 420 SEL | Cigar Havana | Tech Help | 0 | 10-04-2003 09:39 PM |
Calf. Changes view on diesel | richard u | Diesel Discussion | 4 | 10-24-2002 06:10 PM |