Vehicle speed sensor 'A' code P0500 (BAS,ESP,ETS,ABS - lights)
 

Vehicle speed sensor 'A' - fault code P0500 'A', ML320, 2002 model
Does 'A' mean it is on the left side front or rear wheel sensor
Please help?
Has anyone else replaced same?
* If so would this be classified as a rocket science project?
* does the sensor sit on the outside of the hub or inside the bearing?
* Front ball joints replaced 8000 km ago - could the job have messed things up?
* Any pictures or schematic drawings appreciated

If the Garoge did the work how much did u pay?

ON that truck you should get a traction code like "C 1000".
Generic engine codes like that don't lead to a diagnosis of the problem.. Code must be read from traction & transmission systems.

Thanks Doc for responding
 

Thanks for the additional info Doc.

The facts: leading up to the dash lights been illuminated like a Xmas tree was that the wife was driving through tons of water during a thunderstorm.
However, I am no rocket scientist and if I interpret 'generic' u mean that only MB diagnostic/code reader machine can provide the test and not a generic diagnostic/code reader machine and/or there is a specific machine to be plugged into the transmission/traction port - and this port is someone where else in the vehicle other than the port situated under the drivers dashport.
Or is it possible that the generic diagnostic/code reader machines give out diff codes numbers and letters to the Mb for the exact same problem
In other words if one was to plug the MB diagnostic/code reader one would receive "C 1000" while a generic diagnostic/code reader machines would give a reading P0500 (vehicle speed sensor A left side)

Forgive Doc but I am confused can you elaborate


Thanks Doc

Miracles do happen but for how long remains to be seen
 

The mechanic I know ran a snap on trouble shooting code reader; producing Vehicle speed sensor 'A' - fault code P0500 'A', when he looked it up on the internet stated that the mentioned sensor above was on the left side of the vehicle either left front or left rear, but no further elaboration.
Here is the kicker he reset the dash lights and stated they will return - which they did, however, exactly one day after the initial dash warning lights came on they disappeared or were no longer iluminated all butthe check engine light but moments after this miracle the the engine light disappeared or were no longer iluminated - go figure

Miracles don't always last - it rained again
 

all the lights mentioned went on again but as sson as it dried up the lights dissapeared Any suggestions?

Have MB repair shop check codes from traction system for proper diagnosis..there are at least 50 different codes that could come out of that system.

It's just as M.B.DOC said.

http://www.whnet.com/4x4/pix/MIL.jpg

If the ABS light comes on it indicates a problem with the ABS system like a wheel speed sensor with loose connection, which also lights up the other lights.

The P0500 is read from the engine controller and indicates there is a VSS vehicle speed sensor problem:
P0500 Vehicle Speed Sensor Malfunction

http://www.whnet.com/4x4/dtc.html

To figure out what exactly is wrong one needs to read the traction controller which gives the Cxxxx fault codes.

Some ABS info for troubleshooting is here:

http://www.mercedestechstore.com/pdfs/327_traction_and_braking/327%20HO%2002%20ABS%20(WJB,GC)%2002-25-04.pdf

I hate to beat a topic that has been talked about several times, but just want to make sure I gathered the correct info that I have read in these forums.

I have only had my ML430 for a little over a year and with no problems. I bought it used and I love it. Lots of power and fun to drive. Recently I replaced the original battery and this is where I was introduced to indicator and warning lamps. After battery replacement the BAS/ESP and ETS lights were illuminated but soon extinguished after driving a short distance. Everything was back to normal until recently when on a trip to the beach, the BAS/ESP and ETS lights came on again. This time they are staying on. Rechecked the battery and it is deffinately good. So after reading in these forums, I see where it is a likely candidate that the stop light switch could be bad, which is located at the brake pedal.

Other than taking the ML to the dealer to have the codes read, is there anything that I may be missing or overlooked that I should check or read? I would appreciate your help.

After replacing the battery you must re-activate the Steering Angle Sensor as follows:

1. Start engine.
2. Turn steering wheel from lock to lock.

The ADS or ESP malfunction indicator lamp (A1e27 or A1e42) should go out.

At this time it may also be the stop light switch.

Hope this helps.

Rene

I also have a 99 ML320 with consistent BAS/ESP/ETS lights on. The other thing that happened at the same time is that the cruise control no longer functions. Lights came on all at once and have never gone out.

Took the car to the local independent MB shop where he used the computer to check codes and told me it was the steering angle sensor...requiring replacement of the whole steering column. However, I had not realized the cruise control was out at that point so I'll have to talk to him about it before he goes ahead with the repair. He did try the reset business with turning steering wheel lock to lock etc with no change.

I was with him when he checked the computer and saw the code for the steering angle sensor. When people are talking about replacing the brake switch, is that in lieu of checking the computer codes? Do the codes mislead? I'd hate to pay for the whole steering column replacment to find out I just needed a new brake switch.

I would replace the Brake Switch first (cheap fix) and see what happens before letting your independent fix anything. See http://www.benzworld.org/forums/w163-m-class/1166641-ets-bas-warning-light-fix.html?highlight=brake+switch+replacemet for DIY instructions. My 2 cents.

Thanks. Do you know if the brake light switch could also have anything to do with the cruise control not operating? I've seen lots of posts regarding the brake switch but no one else mentions the cruise control. The cruise control stopped working (won't turn on) at the same time (approximately...I obviously did not notice it simulateously) that the BAS/ESP/ETS lights came on.

I do not think that the cruise control is related to the BAS/ESP/ETS lights. It just does not make sense that it would. But I am not 100% on that. And as far as the switch....since it is a $25 item, I am going to replace that first, then if I have too I will get the codes read. I will replace the switch this weekend and post results.

Oh, I found the switch here.

At least I am thinking this is the correct part. Will know for sure once I remove the existing one. :-)

Yes............. a faulty brake switch will affect your cruise control. :thumbsup:

I replaced the brake switch today and the BAS/ESP/ETS lights are out. Everything looks like it is back to normal. Just wanted to say thank you for you help. :)

The part was only $14 at the dealer. Very cheap fix.