Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

 
 
LinkBack Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1  
Old 07-15-2006, 09:01 PM
Registered User
 
Join Date: Jan 2002
Location: Niceville, FL
Posts: 471
Another High Idle Problem...as well as Tach and ABS Light

First, I've read innumerable threads on high idle and there appears to be no clear solution to the problem. Few of the folks actually report back on what finally cleared the problem.

According to one of the threads, the MB manual says idle is affected by one of the following five things: oil temp sensor; oxygen sensor; coolant sensor; air flow pump; idle speed solenoid. Other posts suggest a vacuum leak or a probem with the micro-switch. I would also think the Idle Speed Control Unit is a player, since it feeds the control valve on the engine.

- Car is an '85 500SL Euro, not that the latter should actually matter
- Problem started several weeks ago with a surge of a couple hundred RPM, but has progresively gotten worse...up to surges of 1500-2000 RPM. Car runs and idles perfectly when the engine is cold. The surge begins when the engine gets hot...not before.
- Cleaned the idle speed control valve three or four weeks ago and that seemed to help briefly
- Took the car to my mechanic this week and the idle was oscillating beautifully up and down from about 700-1700 RPM as I pulled into the shop. So, he knew what the problem was.
- He checked the coolant sensor and there was no connection. So, he fixed that. Seemed to temporarily correct the problem, but after the engine warmed up the idle surge began again.
- Then he glommed in on the idle speed control valve...which I had told him was replaced a couple years ago (along with the control unit) and recently pulled, cleaned and reinstalled. Even though I had a good spare in the trunk that he was aware of he installed one from his bench stock...for a very reasonable $150.00...put two new hoses on it, adjusted the lean/rich mixture and thought he'd solved the problem. Said it held idle at about 700 RPM and never moved. So, I picked the car up from him.

After pulling in the driveway and putting the car in neutral the RPM surged to about 1200 RPM and settled at about 800RPM. When it stabilized, the tach just seemed to go haywire, jumping all over the place out of consonance with the engine.

Finally, the ABS light comes on now after driving the car for awhile and making a couple of stops. I've replaced the OVP with a couple spares and that particular problem still persists.

I called the mechanic when I got home and advised the problem is not fixed. Said no problem, bring it back and he'll figure it out, and won't charge me an arm and a leg to do so. I'm hoping it's something as simple as the oxygen sensor which wasn't checked. However, if someone has suggestions...

Also, I'm curious what might be causing the ABS light to come on since it doesn't seem to be OVP related and what might be causing the tach to fluctuate wildly. I know this is long, but I've tried to be as explicit as possible in relating the problems. Thanks for any help that might be provided.
__________________
Don
'85 500SL (Euro) - 186,000 w/a complete restoration and engine rebuild at 154,000
'95 C280 - 174,000
Reply With Quote
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 02:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page