I was told that it is good idea to change the receiver-dryer/accumulator when I switch compressors and flush out the A/C system on my '89 300SEL. (This is to remedy a compressor failure.)

Is this good advice?

Thanks.
-Brett

As cheap as they are, you might as well.

__________________
It is a truism that almost any sect, cult, or religion will legislate its creed into law if it acquires the political power to do so. Robert A. Heinlein


09 Jetta TDI
1985 300D

Hi Larry. Thanks for the reply.

My hesitation was not the price, but the time it will take to get one, and a lack of understanding as to why it would need to be replaced.

Without replacing it I can be done today. But if I need to replace it, the part is at least a day or two off (nobody around me seems to stock MB parts - even an air filter is a special-order item).

-Brett

do the expansion valve , too... not much cost there, either

__________________
1989 300ce 129k
( facelifted front,updated tail lights, lowered suspension,bilstein sports, lorinser front spoiler, MOMO steering wheel, remus exhaust,stainless steel brake lines). (Gone)

1997 s320 154k (what a ride). Sold with 179k miles. Replaced with Hyundai Equus

1994 e320 Cabriolet 108k



1972 280se 4.5 153k Owned for 12 yrs, sorry I sold it


[/SIGPIC]

You should always replace the drier when you open the system, and ESPECIALLY after the kind of work you have just done.

__________________
2012 E350
2006 Callaway SC560

You need to replace it to get new desiccant. Yours will have absorbed some water, and will absorb more with the lines disconnected.

The reason for replacement is what Matt said. The purpose of the drier is to remove moisture from the refrigerant and it can only do it as long as it has not absorbed tons of moisture already which is what would happen when the a/c system is opened and kept open for an extended period of time and also during flushing. If you dont replace the drier, excessive moisture in the system would damage the compressor and also fine tubing in the condensor as well as the evaporator. Replacing the expansion valve is also a good idea though not absolutely necessary. And ofcourse replacing all the seals (o-rings) around tubings that are opened should always be done. Replace the inserts of the schrader valves also.

__________________
Saumil S. Patel

They may not be removable so don't tear them up trying to get them out.

__________________
2012 E350
2006 Callaway SC560

Thanks guys. Now it makes sense to me.

I've ordered the receiver/dryer, expansion valve and a seal kit (all the o-rings, etc.). It was about $60 total (which seemed reasonable to me). Now I just need to wait a few days.

Thanks again.
-Brett

MB offers these guidelines...if the system is over 5 years old & is opened for any reason, the drier should be replaced.

If the system is left opened w/o charge OR vacuum for over 24 hrs the drier should be replaced.

__________________
MERCEDES Benz Master Guild Technician (6 TIMES)
ASE Master Technician
Mercedes Benz Star Technician (2 times)
44 years foreign automotive repair
27 Years M.B. Shop foreman (dealer)
MB technical information Specialist (15 years)
190E 2.3 16V ITS SCCA race car (sold)
1986 190E 2.3 16V 2.5 (sold)
Retired Moderator

The compressor-to-condenser hose from my York compressor ('77 280E) has just developed a leak where the metal tube goes into the metal shroud that connects to the rubber part of the hose. Is there is seal in this part of the hose that I can replace? The system recently was given a charge just before the leak started.

If it is a Schader valve, like the one in our bicycles, the inserts should be removable. You just need a special tool, available for sure at home a/c supply stores. The insert has to be rotated to remove.

__________________
Saumil S. Patel

I am tracking like a freight train on the idea of replacing the drier and the receiver and even the expansion valve and the seals. My issue is past that. After opening the system and vacuuming it down and refiling the freon, I am lost. My 16v is switched to R134 and until this week has always been ice cold. It has been 95 -97 each day and if i let the car idle or have to stop for an exrtended period of time, the a/c goes hot and stays hot until I stop the engine. Then after a short shut down, even 5 minutes, I restart the car and the ac is typically ice cold again. ANyone know what my issue might be. I am working on getting the new drier, reciever and seals and valves, but I dont know what is causing the hot ac on idle or car not moving.

__________________
Christopher Henkel
1990 190E 2.6 - Arctic white SOLD
1986 190E-16v - Blauswartze
1993 300CE - SOLD
2003 W208 CLK 320 Cabriolet - Magma Red

Christopher, the first things I would check are the fan/clutch and the electric aux fan.

__________________
2012 E350
2006 Callaway SC560

After you shut down for a few minutes and on restart when the a/c works again, does it work on idle for a while ? When the a/c stops blowing cold air, do you see the compressor cut off ? I am trying to understand whether it is mismatch in the engine and the compressor RPM that is causing the compressor to shut off and therefore causing a loss of cooling OR is it the engine temperature OR high compressor outlet pressure (possibly because your aux fan may not be working) that is causing the compressor to shut off.

__________________
Saumil S. Patel