Have a 96 S-320 with 96,000+, should the wheel bearings be re-packed soon. I'am hearing a low level pulsing rumble/roar on the road, may be the michelins, they caan be rather noisy at least til they get hot. Thanks for any input.
Ron

If the bearings are making a noise its time to replace them.

That would be rather early for wheel bearing problems. The green grease, which started in about 1986 I think, is generally good for way more miles than that and often the life of the car. Of course 140s are heavy and tend to be hard on things but I would do some more checking - seems unlikely at that mileage. Don't think there's a factory specified interval for it.

It's not so much the performance of the grease, as it is too much to expect the seal to keep dirt and water out of the bearing for the life of the vehicle. Once dirt and water enter the bearing the grease is compromised and cannot perform as well as new grease. Intrusion of contaminants has a cumulative effect.

Regreasing the bearings is a good excuse to inspect them.

I would recommend 60-90K regreasing intervals with new seals. Since the number one reason for bearing failure is improper mounting/maintenance, I'd side with deanyel and recommend to never touch the wheel bearings unless you know how to properly do this task.

__________________
95 E320 Cabriolet, 169K

Talking with Shell tech' rep' some years ago he told me bearing grease never needs changing just to refresh the grease.

He commented, you can get more grit/dirt IN the bearing from messing with it that way shortening it's service life..

BTW...We don't have that service in Europe...seems it's an 'American' thing.

As long as seal is good and sufficient grease was loaded into the hub at assembly, that's it for life.

I tend to agree. I never touch wheel bearings unless to adjust them and then I clean the cap and reload it.

BTW...He said never use a graphite or Moly grease as these can cause the rollers/balls to skid.



.

__________________
[http://languageandgrammar.com/2008/01/14/youve-got-problems-not-issues/ ]

"A liberal is someone who feels they owe a great debt to their fellow man, which debt he proposes to pay off with your money."

I seem to remember the recommendation of experts on this site was to service the bearings every other brake job.

jp

__________________
Jeff Pierce

Current Vehicles:
'92 Mercedes 190E/2.3 (247K miles/my daily driver)
'93 Volvo 940 Turbo Wagon (263K miles/a family truckster with spunk)
'99 Kawasaki Concours
Gravely 8120
Previous Vehicles:
'85 Jeep CJ-7 w/ Fisher plow (226K miles)'93 Volvo 940 Turbo Wagon
'53 Willys-Overland Pickup
'85 Honda 750F Interceptor
'93 Nissan Quest
'89 Toyota Camry Wagon
'89 Dodge Raider
'81 Honda CB 750F Super Sport
'88 Toyota Celica
'95 Toyota Tacoma
'74 Honda CB 550F

Around 75 to 100k miles they will usually need tightening. At that time I would add some grease. At 200K or so I would think about changing the seals. If you keep them tight and lubed the bearings will about last forever.

Tom W

__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.

Are w140s like w126s in that whenever the rotor is removed the bearings are exposed, like on old American cars? On newer American cars you can just pull the rotors with little difficult whereas older MB's (and maybe newer ones) require disassembly of the hub (I'm not sure if that's what you'd call it).

Thanks
David

__________________
_____________________________________________

2000 Honda Accord V6 137k miles

1972 300SEL 4.5 98k miles

_____________________________________________

IIRC, then yes, the rotor can be removed without disturbing the bearing.

__________________
95 E320 Cabriolet, 169K

Gentlemen:

Thanks for all the input. Guess I'll go ahead and repack them then I won't have to worry any more. I'll probely sell this one after it rolls over about 100K. I get nervous on long trips after they pass 100K. No real problems so far, can't complain.

Ron

Nervous after 100,000 miles; not with a Mercedes. My '94 E320 just passed 150,000 miles and I would not hesitate to drive from Fairfax, VA to San Diego, CA tomorrow, or Fairbanks, Alaska; season permitting.
regards.
Mark

Never. I put 380kmiles on a 240D and never touched the wheel bearings.

Apparently, they know how to make them.

240Joe