Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-23-2011, 10:34 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
1987 260E Low power issue - Round 2

Starting new thread with updates and everything compiled.

Background:
Car ran great for over a year, averaged 21-22mpg.
Last Sept water pump blew and the car was running at 110C for a few days while I tried to diagnose what was happening, never overheated though.

MPG dropped to 12-13avg and power SUCKS. I would guess a 50% drop in power. Its just lifeless.

Parts Replaced / Tests done
  • Plugs/Wires/Rotor/Cap <--- done last year brand new
  • Compression Test GOOD -- average 180psi all cylinders, variance no greater than 5%
  • New fuel pumps, fuel filter, fuel tank strainer, fuel tank inspected, all fuel hoses replaced
  • Fuel Distributor + EHA brand new
  • O2 sensor new
  • Injectors are brand new + also checked spray pattern
  • Coil swapped with spare
  • Car goes into closed-loop. Duty cycle 55% and fluctuating
  • Fuel pumps now gets 1L in 30secs (spec is 1L in 40secs)
  • Fuel Pressures are 5.1/5.5 bar -- pressure holds @ 3.1bar. So pressures + holding pressure GOOD.

Ideas where to look now?

__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k
Reply With Quote
  #2  
Old 07-24-2011, 01:24 AM
Registered User
 
Join Date: Dec 2007
Location: NorCal
Posts: 1,332
Plugged cat a possibility?
__________________
http://i193.photobucket.com/albums/z...-RESIZED-1.jpg
1991 300E - 212K and rising fast...
Reply With Quote
  #3  
Old 07-24-2011, 04:25 AM
Registered User
 
Join Date: Jan 2008
Location: Melbourne Australia
Posts: 844
Here's a couple of images of my cluster. Notice the vacuum gauge.
Heres the vacuum gauge in Park - with the engine warmed.


Here's an image with the transmission in idle.


Note that the car has just passed the 200000 Kilometres mark.

If your vacuum is not at those levels you will not get optimum M.P.G. and low end performance.

This car idles very silently - the heater fan is noisier the the engine at idle. Very good M.P.G.
The last item I replaced was the valve for the return fuel to the charcoal canister. It seemed like there was a leak from that. I also replaced the inlet manifold gasket.
Reply With Quote
  #4  
Old 07-24-2011, 11:26 AM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
Good post...Another person also referenced this site to me:
http://www.secondchancegarage.com/public/186.cfm

My vacuum at idle is low according to that site! ...I posted it up a while back (Sep 2010), but didn't get any responses on it.

I'll compare readings with my wagon too for reference.



I've never seen it greater than 14....

So either worn rings or exhaust restriction....I hope the later. I never overheated the engine, so I can't see why the rings would be toast?
With my compression being ~180psi, is it safe to say my rings are probably OK? I did the test dry too, did not squirt any oil in because the readings looked ok.

I have a VERY good feeling we are onto something here now!!
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k

Last edited by ps2cho; 07-24-2011 at 11:37 AM.
Reply With Quote
  #5  
Old 07-24-2011, 12:15 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
Thats it! Its the cat!

This is adding up now.
Another reason: About 6months prior to the issue, I was noticing vibrations on the freeway (load only) at ~90mph.....3months later, its vibrating at 75mph, then after the overheating, 65mph.

It would VANISH as soon as I let off the gas. Its obviously exhaust backpressure causing it. So the issue has been creeping up on me, but it finally gave out after the running hot.
I thought maybe my center bearing was going bad, but the fact that it did not vibrate when I let off the gas just didn't add up in my head at all....

It all makes sense now!
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k
Reply With Quote
  #6  
Old 07-24-2011, 12:26 PM
compu_85's Avatar
Cruisin on Electric Ave.
 
Join Date: May 2008
Location: La Conner, WA
Posts: 5,234
I bet when your injectors screwed up and the A/F ratio went wacky it melted the cat.
__________________
1991 350SDL. 230,000 miles (new motor @ 150,000). Blown head gasket

Tesla Model 3. 205,000 miles. Been to 48 states!
Past: A fleet of VW TDIs.... including a V10,a Dieselgate Passat, and 2 ECOdiesels.
2014 Cadillac ELR
2013 Fiat 500E.
Reply With Quote
  #7  
Old 07-24-2011, 12:33 PM
Senior Member
 
Join Date: Nov 2002
Posts: 829
easy way to tell if it's the cat-remove the o2 sensor and drive it. it it's better, you need a cat. good luck, chuck.
Reply With Quote
  #8  
Old 07-24-2011, 12:51 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
Quote:
Originally Posted by compu_85 View Post
I bet when your injectors screwed up and the A/F ratio went wacky it melted the cat.
Hmm....Ran the vacuum test as shown on the site, but I am not really getting the reading I was hoping for?
http://www.secondchancegarage.com/public/186.cfm

Its almost like I get #11 -- retarded ignition timing, but the timing is not adjustable?
http://www.youtube.com/watch?v=bQSrkRXla0E
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k

Last edited by ps2cho; 07-24-2011 at 01:27 PM.
Reply With Quote
  #9  
Old 07-24-2011, 09:29 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
I just ran the car @ 3000rpm and it stayed steady at 17inHg....According to the site, if the exhaust was blocked, I should have slowly dropped.
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k
Reply With Quote
  #10  
Old 07-25-2011, 09:01 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
I left the gauge attached and took her for a drive, and its completely different results.

Upon acceleration it drops to 0 and stays there until I almost completely back off the gas. I then, for comparison (since my wagon has had cats replaced) plugged the vac gauge into my 300TE and did the same journey and she did NOT go to 0, but stayed around 2 then began to gain vacuum again unlike the 260E.

In addition to the vacuum gain, the gauge responded much quicker on the 300TE too.

Video of 260E:
http://www.youtube.com/watch?v=euhKbv7ECmA

Anybody think this points to blocked cats too?
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k
Reply With Quote
  #11  
Old 07-26-2011, 04:44 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
Took car to exhaust shop, he doesn't believe the cats are blocked....

He used a temp gun on the inlet/outlet of each cat:

Precats: 25C difference from in/out....he states it seems like there is probably not even anything in there anymore, possibly hollow?
Main cat: 100C difference...barely anything.

So in all, he said if the cats were blocked, there would be a large difference between in/out temps. He said for me to look elsewhere for performance issue.
The guy said the performance was right, but the transmission shifted hard (but we all know generic mechanic bob doesn't really understand these cars) and I politely declined the $98/hr diagnosis he suggested. The transmission shifts very firm, maybe a tad too firm, but its not a thud, its a firm shift -- always been like that, so thats not the issue at hand.

Guess its time to move onto the next check....I'm thinking I should get a leakdown test done now, although I'll have to buy a compressor -- a useful tool for many, many uses!
Then maybe ignition + valve timing? Although my distrib + cap were brand new and we all know both values are not adjustable.
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k
Reply With Quote
  #12  
Old 07-31-2011, 08:00 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
GUYS!

I just figured it out!!!
The oxygen sensors heater element wasn't working!

Alright so....back in...November I replaced the o2 sensor thinking maybe that was the problem...no difference, THEN I discovered the fuel contamination. Well....I bought the generic Bosch O2 sensor and spliced it in.

I asked the question about the 2 white wires having a specific orientation and the responses were shouldn't make any difference, so I spliced it in and forgot about it.

I checked it out right now by plugging it back in while holding the sensor with my hand and voila! No increase in temperature at all!
So....I then reversed the two poles at the plug so it was now in reverse orientation, and HEATER WORKED.

Plugged it back in and massive difference. The car at first was slow, but the more I drove it, the more it picked up.
I would say I just recovered 95% of the power.
I'm thinking though since the sensor has been driven without any heating, it might be trashed already, what do you think? I'll probably get a new one, splice it in, test the heater, then call it a day

Phew....! I KNEW this was something simple. I just couldn't figure it out! Damn happy now. Gonna get a new sensor, drive on the freeway really hard then get'er smoged! Fingers crossed on that one LOL.

Maybe someone's looking down on me -- my 300TE's radiator hose blew off today on the way to an interview and it was a royal PIA fixing it in slacks, shirt, tie, vest...what a fiasco.
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k
Reply With Quote
  #13  
Old 08-01-2011, 11:40 AM
benzworldrefuge's Avatar
Registered User
 
Join Date: Apr 2011
Location: Bayshore, NY
Posts: 44
Wow congrats on nailing it yourself! Last generic O2 sensor I bought was maybe a year ago and it was under $25. If you can get one at that price why not swap out the fouled one?
__________________

88 300e
89 300e
93 400e
93 500e
77 308 GTB
Reply With Quote
  #14  
Old 08-01-2011, 11:53 PM
ps2cho's Avatar
Registered User
 
Join Date: Jun 2006
Location: Chandler, Arizona
Posts: 3,525
Got the new sensor in -- definitely much better, but not quite back to normal yet.

I have a feeling its a possible EHA deal now. I'll do some more testing
The EHA was brand new, but it was exposed to the crap I found in the fuel system, so I am not sure whether its clogged inside possibly? I have never taken an EHA apart, so I don't know if there is anywhere inside that could clog?
__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k

Last edited by ps2cho; 08-02-2011 at 12:59 AM.
Reply With Quote
  #15  
Old 08-03-2011, 05:18 PM
Registered User
 
Join Date: Oct 2008
Location: Canada / Lebanon
Posts: 223
There is nothing you can "clean" or change in the expensive EHA. there is just a screw that can adjust fueling (for more or less fuel to be delivered).
did you to rebuild your fuel distributor? test your injectors?

you got pm regarding compression test

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 01:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page