722.3 Transmission spinning not engaging
Well the 603a turbo motor running perfect when all of sudden yesterday the transmission failed to engage. The engine would rev but no forward movement. I checked my fluid and discovered it was too high. I drained it to the proper level but still nothing. The fluid was the nice red color not brown and did not smell burned.
I checked my vacuum and linkage connections. All were as they should be. I can put it in gear and without touching the gas pedal it will move forward and in reverse on its own. If I apply the gas the engine spins and it does not engage. Luckily I was able to get it into my garage before it refused to go any further. Any help is appreciated. Mark |
Take a look at the trans output flange, there have been a few reports of the nut working loose and flange splines stripping out. Elevate the rear wheels, parking brake off, put trans in park then try to rotate the drive shaft. You might have to use a bar to gain leverage.
Swapping the flange is easy. To check the rear diff flange, leave trans in neutral, block the rear wheels or apply parking brake then rotate the drive shaft. The next things to check would be trans line pressure, if the pressure regulator spring failed, line pressure would drop and not burn the fluid. Past that, the input splines in the trans gear train may have stripped out. |
Since this is an old g-wagen the tranny has a short drive shaft that goes to the transfer case. All looks good there. Through a little research this morning I am leaning toward the pressure modulator valve on the side of the transmission. Since it is slipping in all gears it makes sense that it would be the problem.
Thoughts? M |
Why was the fluid too high?
Does your G wagon share a radiator with a transmission oil cooler? Are you sure the fluid is now correct? Have you checked the Bowden cable / accelerator linkage? Have you checked the gear selector rod and bushings? (Probably not this if the car moves but I like to go down the whole list!) Have you checked the working pressure? (you need a gauge for this) (All simple stuff - I reckon you are better off looking for the simple if you haven't done so already before you start thinking about more complicated stuff) |
Quote:
|
Perhaps I should start with a drain and renew of the tranny fluid. Draining the torque converter as well.
M |
1 Attachment(s)
If the fluid looks red a fluid change won't help but, if the filter collapsed changing the filter will help.
Don't move the car by driving, if the trans isn't damaged, moving it will cause problems. Here is a tech file for the 722.3 / 722.4 showing test points and other info. The test points are 10 mm x 1.0 pitch ( some brake lines use this thread for a quick EDIT > thread pitch < EDIT test ) You can use a banjo bolt or weld a hydraulic or pipe fitting to a bolt to make an adapter. |
You could have a pump failure. The fluid could have drained back to the oil pan
thats way the level was too high. |
pump
Quote:
Mark |
Quote:
Incorrect modulating pressure. Modulating pressure control valve or pressure relief valve is dirty or sticking. Vacuum line to transmission vacuum capsule clogged or leaking. Working pressure control valve dirty or sticking. Low working pressure. Defective primary pump. Pump failure I guess sometime you will hear a whining noise before total failure. Pump failure must be rare also. |
Pump gear failure assuming no gears at all. Remove cooler line from radiator, start engine...if nothing comes out you know its the pump gear. Have a helper start the car while you hold a bucket under it. It will fill extremely quick so be ready to shut it down immediately.
Modulator would not cause no gear, only a lack of shifting, same with governor. |
Here's a link for the front pump reseal
http://www.peachparts.com/shopforum/general-information/319957-722-315-pump-re-seal-pictures.html But measure that working pressure first! |
Great thanks thanks for the advise. To start, I will run with ps2cho's test today and go from there.
Mark |
Also I see that there is a secondary pump. What is this additional pumps function and could it be suspect as well?
M |
Secondary pump is required only for towing and tow-starting
vehicle. It is designed as an external gear pump and is positioned in rear section of the transmission. If needed, secondary pump is driven by centrifugal governor shaft. Secondary pump operates only if engine is not running and vehicle is rolling (tow-starting procedure), while brake band B-2 slowly engages. Pump stops operating when vehicle comes to a stop or if transmission has shifted into 4th or 5th gear (engine running). |
All times are GMT -4. The time now is 06:47 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website