Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 12-26-2019, 05:02 PM
Registered User
 
Join Date: Feb 2015
Posts: 20
W126 Center Driveshaft Bearing Replacement

Hey All. I have a 1986 300 SDL and I went crawling around today to replace the flex discs. I pulled the center bearing support to get the play I needed to get the disc off, (location marks were made on both front and rear driveshafts, just in case) and this was where I noticed one of two things I need advice on.

The driveshaft very nearly just fell out of its splined interface with the front half. Some of my research suggests the existence of a ‘slip nut’ that is supposed to prevent this. I did not investigate much further as it was to be hidden by a very worn And disintegrating rubber boot, which I have been unable to find in a parts catalog should I need replacement. If that slip needs to be tightened or inspected I will make sure to do so during re-install.

The center bearing support is destroyed. It gets worse just by looking at it. However everything that I can find for replacement is a stand alone bearing and a support bracket. My bearing and support are one single unit. The outer race of the bearing is molded into the run or support. The part number from my old unit is 124 410 02 80 which pulls some eBay and such listings. Will the two piece kits on Pelican Parts fit or do I need to replace like for like?

Cheers,
T.P. Crockmier

Reply With Quote
  #2  
Old 12-26-2019, 05:17 PM
Diseasel300's Avatar
Registered User
 
Join Date: May 2016
Posts: 6,025
The bearing and support carrier are separate pieces. The support carrier and bearing are typically sold separately, so yes, they're the correct part. The slip nut on the driveshaft will be tightened after you finish reassembling and have the weight of the car on the ground. Put the transmission in neutral and roll it back and forth a bit before tightening. It need be only snug, you don't have to go crazy with it.

Here's a How-To from this site: W126 drive shaft carrier/center bearing DIY

While you're under there and have the driveshaft apart, check the U-joint for stiffness or notchiness. It should be smooth and free. A ratchety feeling or stiffness indicates it needs replacement.
Reply With Quote
  #3  
Old 12-26-2019, 06:48 PM
Registered User
 
Join Date: Feb 2015
Posts: 20
Hey thanks so much for the info. I won’t be able to get under the car when it’s on the ground so I’ll have to try and figure out how to get that tightened up as you said.

I have that thread open and have been using it for reference. It’s been a great help so far but I was a bit confused when it was talking about and showing pictures of snap rings, as there is no such retention on my original bearing, it’s just pressed on. And there is a part assembly that gets referenced that isn’t quite relevant to my driveline, which is why I had some questions and came here, but a great resource nonetheless.

The U-joint is indexing. It wants to index to a straight position. I’ll likely have a local driveshaft shop press the new bearing and carrier so I will ask him about getting that overhauled. It’s a daily driver so I only have about a week left of vacation to get it back up to speed.
Reply With Quote
  #4  
Old 12-27-2019, 12:43 AM
pawoSD's Avatar
Dieselsüchtiger
 
Join Date: Oct 2004
Location: Grand Rapids, MI
Posts: 15,438
Typically on these cars when the flex disc needs replacing so does everything else on the drive shaft, including the support, bearing, boot, etc. The joint should not have slid apart like that, it should have been tight with the giant 46mm nut/collar.
__________________
-diesel is not just a fuel, its a way of life-
'15 GLK250 Bluetec 118k - mine - (OC-123,800)
'17 Metris(VITO!) - 37k - wifes (OC-41k)
'09 Sprinter 3500 Winnebago View - 62k (OC - 67k)
'13 ML350 Bluetec - 95k - dad's (OC-98k)
'01 SL500 - 103k(km) - dad's (OC-110,000km)
'16 E400 4matic Sedan - 148k - Brothers (OC-155k)
Reply With Quote
  #5  
Old 12-27-2019, 07:11 AM
Registered User
 
Join Date: Aug 2002
Location: Southeastern PA
Posts: 3,077
T.P.Crockmier, place a ramp or stack of pieces of 2"x6" wood under each wheel so you can crawl under your W126 to tighten the slip nut.
__________________
Fred Hoelzle
Reply With Quote
  #6  
Old 12-27-2019, 09:20 PM
Registered User
 
Join Date: Feb 2015
Posts: 20
Cool, cool. I’ve got the carrier on the way and it should be here in a couple of days. In the mean time I’ve got some scrap lumber that I can fashion into blocks to put the car on.

Hopefully with everything replaced my driveline will quiet down a bit and I’ll certainly gain some peace of mind.
Reply With Quote
  #7  
Old 01-04-2020, 06:32 PM
280EZRider's Avatar
No Dumping
 
Join Date: Jul 2007
Location: Southern Oregon Valley
Posts: 1,599
Quote:
Originally Posted by T.P.Crockmier View Post
Hey thanks so much for the info. I won’t be able to get under the car when it’s on the ground so I’ll have to try and figure out how to get that tightened up as you said.
I use 2 sets of ramps for this. After driving the car onto the front ramps you jack the rear from the differential and slide the second set of ramps under the wheels. Place them with the angled part facing forward, hence, wheel stops in both directions. You may need a another jack to raise each trailing arm slightly to insert the ramps.

Tighten the 46mm nut with the center bearing support close but not tight. You can bounce the car up and down from the rear, which has the same effect as rolling it. Now you can tighten the center bearing support, which should be done last.
__________________

Don't Chrome them; polish them
Reply With Quote
  #8  
Old 01-06-2020, 05:17 PM
Registered User
 
Join Date: Feb 2015
Posts: 20
I ended up making wheel cribs out of 2x4s. Had to walk the car up on to jack stands and then get a bigger piece of wood to get it up the last few inches. Worked like a charm, and I had a good amount of room under the car.
Reply With Quote
  #9  
Old 01-06-2020, 06:30 PM
Registered User
 
Join Date: Jan 2003
Location: Dallas
Posts: 796
Tightening torque on the big center nut is only 30-40 NM. It's intended to slip a tiny bit as the car moves around; makes life easier on the flex joints. At that torque it is also possible with a little bit of "oomph" to slide the joint back to remove a flex joint or tranny.

DG
Reply With Quote
  #10  
Old 01-09-2020, 11:24 AM
Daantjie
 
Join Date: Nov 2014
Location: Vancouver, BC, Canada
Posts: 151
Does anybody know if with the clamping nut loosened, can you slide the shaft into itself such that it basically drops out, or is it still a lot of reefing required to get it to drop out?
Cheers
Reply With Quote
  #11  
Old 01-11-2020, 06:04 PM
280EZRider's Avatar
No Dumping
 
Join Date: Jul 2007
Location: Southern Oregon Valley
Posts: 1,599
Quote:
Originally Posted by daantjie View Post
Does anybody know if with the clamping nut loosened, can you slide the shaft into itself such that it basically drops out, or is it still a lot of reefing required to get it to drop out?
Cheers
With the 46mm nut all the way back to loose, the two halves can be moved so much that they can even be separated- so be sure mark both halves before removal. Marking is a good idea even on later driveshafts that have factory markings.
__________________

Don't Chrome them; polish them
Reply With Quote
  #12  
Old 01-12-2020, 01:51 AM
Daantjie
 
Join Date: Nov 2014
Location: Vancouver, BC, Canada
Posts: 151
Thanks EZ I'm tackling this one tomorrow I'll be sure to mark that bad boy up good!

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 02:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page