Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-19-2003, 06:13 PM
Registered User
 
Join Date: May 2000
Posts: 376
What are the correct low/high A.C. pressure radings for a 190e with R12???

Hi all.

Anyone know what the correct low/high side air conditioning readings should be for a 190e with R12?

Larry Bible indicated (thank you Larry) my current readings are close to spec. But I am curious what the exact specs are?

I only have the factory A.C. shop book for a W124, and my specs are way off from those. Per this spec book, all reading should be at 2,000 rpm.

Thanks.

Tinker

Reply With Quote
  #2  
Old 07-19-2003, 07:27 PM
Registered User
 
Join Date: Aug 2001
Location: Evansville, Indiana
Posts: 8,150
Hard to tell right off the bat, but with the windows open, blower on high, engine at 2000 rpm, you should have about 35 psi on the low side and somewhere between 250 and 350 psi on the high side, depending on ambient temp and whether or not the aux fan is running.

Low side temps will drop much lower than that when the expansion valve closes, though, but shouldn't rise much higher.

For R12, the pressure and the temp in degrees F is the same on the low side, you never want it below 32 psi with the expansion valve open or the evaporator will freeze. It will drop to 15" of vac sometimes, with the expansion valve closed, before the evaporator temp switch cuts the compressor off.

pressures over 40 indicate a failure of the expansion valve or air in the system, usually.

Very low low side pressure (15" vac all the time, suction line not cold) indicates low charge. High side will also be well under 200 psi in this case, also. If the high side is 350 to 450, the expansion valve is plugged or stuck shut.

I didn't look these up, so someone with better information can correct me if I'm wrong!

Peter

Peter
__________________
1972 220D ?? miles
1988 300E 200,012
1987 300D Turbo killed 9/25/07, 275,000 miles
1985 Volvo 740 GLE Turobodiesel 218,000
1972 280 SE 4.5 165, 000 - It runs!
Reply With Quote
  #3  
Old 07-20-2003, 06:27 PM
Registered User
 
Join Date: May 2000
Posts: 376
Thanks Peter.

I am only seeing low side pressure in the low 20's and high side of around 230 psi @ 85 F & 2500 rpm. This was after I added 12oz of R12. I wouldn't think the auxillary fan would be kicking on at these low pressures. I thought it would be closer to 250psi (??) but its comes on. Problem is my vent temps are only in the mid-low 60's, so I am thinking I am still a bit low on charge???

Thanks again.

Tinker
Reply With Quote
  #4  
Old 07-20-2003, 08:49 PM
Registered User
 
Join Date: Aug 2001
Location: Evansville, Indiana
Posts: 8,150
The low side pressure can be from a clogged expansion valve too, but I'd say you are low on charge.

However, if you have a leak, I'd get the R12 recovered and fix the leak rather than just add more, you really need to evacuate the system if it has been leaking, since air will be diffusing in while the freon is leaking out.

The switch for the aux fan can be either pressure or temp -- don't know which one yours is. I don't get aux fan operation on the 300TE until 300 psi or so, usually.

Peter
__________________
1972 220D ?? miles
1988 300E 200,012
1987 300D Turbo killed 9/25/07, 275,000 miles
1985 Volvo 740 GLE Turobodiesel 218,000
1972 280 SE 4.5 165, 000 - It runs!
Reply With Quote
  #5  
Old 07-21-2003, 06:14 PM
Registered User
 
Join Date: May 2000
Posts: 376
Peter,

I think it has a slow leak.

I have owned the car for four years and never really used the A.C. It had a few electrical issues that I resolved and the A.C. started to work, but only blew cool. I checked the pressures before I added the 12 oz freon and it was reading 10 psi low side and 180 psi high side @ 2500 rpm and 80 F. Figured if it held a charge for over four years, I'd give it a try without pulling it apart and spending some $$$$. Some lose is expected over four+ years?

Thanks again.

Tinker
Reply With Quote
  #6  
Old 07-21-2003, 06:41 PM
Registered User
 
Join Date: Aug 2001
Location: Evansville, Indiana
Posts: 8,150
If it loses pressure, it has a leak, although a small one.

Most likely you have leaky o-rings or a compressor seal, these are the normal problems. The expansion valve will also leak, but that is usually somewhat faster.

Peter
__________________
1972 220D ?? miles
1988 300E 200,012
1987 300D Turbo killed 9/25/07, 275,000 miles
1985 Volvo 740 GLE Turobodiesel 218,000
1972 280 SE 4.5 165, 000 - It runs!
Reply With Quote
  #7  
Old 07-23-2003, 11:15 AM
csnow's Avatar
Registered User
 
Join Date: May 2002
Location: Mass
Posts: 1,127
I'm not sure I would characterize needing some refrigerant every 4 years as a "leak". May not even be detectable. Auto AC systems are inherently leaky to some extent. Ok, this is not ideal, but is it really at the point of repair? Do a cost/benefit analysis.

If it were me, I would topoff the system and add some UV dye.
That way you would likely be able to see where the [very] slow leak is over time.

You can get a really nice Tracerline UV dye kit from thetoolwarehouse.net for around $55.

Best of luck.

__________________
1986 300E 5-Speed 240k mi.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 01:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page