First posting - please bear with me - i'm freaking here...

A 1987 300D, antilock braking, soft brake pedal, spongy - felt like bubbles. Figured to try to purge (edited out:bleed) the system (seemed the first thing to try - fluid a little low). Looked at all brakes yesterday - no leaks/wetness anywhere.

Today: suctioned-out the old fluid from the reservoir, looked a bit dark, filled it with new DOT4. Pedal felt a little better with the engine running.

Hooked a Mityvac to the left front caliper to start purging the lines, pulled about 10" of vacuum, cracked the valve and withdrew a bit of fluid with several bubbles in it. Did it twice more - more fluid & some bubbles. Maybe pulled out just under 2oz. of fluid total. THEN realized it could be leaking air around the threads.

Got someone to help me to play 'pump & hold the pedal, burp the valve". NOW the pedal goes all the way to the floor, hardly any fluid coming out of the tube (what comes out doesn't look as clear as the new I put in) and have tried it 15-20 times with NO improvement.

When the pedal is pumped and held I can still spin the rotor. Haven't checked the other wheels or moved the vehicle yet - left front is still jacked & wheel-off.

HELP! PLEASE tell me I didn't screw-up the ABS! And what can I do to fix this? This is my first car w/ABS (other cars are '83 MB 240D and '86 VW Jetta - both power & assist but no ABS) and vacuum or 'pump/burp' bleedings have always worked fine on them.

(desperate) Thanks!

All the data you need.

ShopForum > Do It Yourself Links & Resources > DIY Links by Parts Category
Brake:
http://www.peachparts.com/shopforum/showthread.php?t=142411






Have a great day.

__________________
ASE Master Mechanic
https://whunter.carrd.co/

Prototype R&D/testing:
Thermal & Aerodynamic System Engineering (TASE) Senior vehicle instrumentation technician.
Noise Vibration and Harshness (NVH).
Dynamometer.
Heat exchanger durability.
HV-A/C Climate Control.
Vehicle build.
Fleet Durability
Technical Quality Auditor.
Automotive Technical Writer

1985 300SD
1983 300D
2003 Volvo V70

https://www.boldegoist.com/

I have the same problem happened to me today, what did you do to have fluid out there (rear right wheel). I tried pumping with my foot with a helper for about 1 hour and no solution only air coming out.
please help
thanks

You have emptied the master res.
There are two res ,seperated by a wall,, the fluid has to go over the seperating wall to get to the other res.. you have to fill the res to the top for this to happen.

Hi,
I filled the reservoir to almost the top.there is no fluid moving out of it to the other res. I assumed both filled. Can you tell from outside the res. if the back one is filled. is the back one so narrow that you confuse it with the body of the res. It is so redicules from MRBZ to design the res. this way. I heard about this 10 times already and stil confused. Sometimes there is something in the design that only the designer can see, it seems stubid to the others. may be I missing something else. I will check again tommorow,
thanks

You have to look at both res.
The only way to fill the back one is to over-flow the front.. this is a dual braking system and requires the 2 res.

If you do not have them both full, you are wating your time .. and only making things worse by pumping air into the entire system..

the system is designed this way for your safety.

if you blow a seal or line on the rear brakes (or the front) and empty the mc of fluid you can only empty the side that is feeding the failed part of the system. the other side is there for you and you can stop the car.

you dont want it to have no fence. trust me.

tom w

__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.