|
|
|
#1
|
|||
|
|||
Re-installing Rear View Mirror on 84 300TD
So I finally redid the sunroof and getting the headliner and all installed and the last piece to go in was the rearview mirror, however this thing will not go back in. I used my leg with my elbow sitting squarely on it and straight to give the most push I could on the rearview mirror, but dang it still wont pop back into place. What has worked for you all??
Ben |
#2
|
||||
|
||||
I did mine the other day.I used a rubber mallet,make sure only one side of the mirror pin is in place then use the mallet on the other side.One good enough blow should do it.
Oh by the way....Make sure to hit only the mirror base...Other wise
__________________
Cheers Big Dan MEng Visit my Blog.. http://allformercedesbenz.blogspot.com/ www.benzguy.piczo.com If at first you don't succeed, Skydiving is not for you. ARTIFICIAL INTELLIGENCE IS NO MATCH FOR NATURAL STUPIDITY. If anything can go wrong,fix it! The hell with Murphy!! I never think of the future.It comes soon enough. |
#3
|
|||
|
|||
replace the mirror
I had to do mine on my 300CD and when I put it back I used a small hammer andd screw driver. you have to be VERY precise where the screw driver engages on the pin. I would suggest a nail set, it has a cup on the end. also a little biodiesel helped
__________________
I love snow 87 300SDL 245K (so far) 85 300cd 253K (so far) 2000 Chevy Silverado (gasser) 1993 Chevy 4x4 Diesel (auction truck) 2000 Monte Carlo (wife's car) Is evolution true, or is Jesus the creator. (John 1:1-3) I would rather trust Jesus on this one, Bill www.BillBaileyMinistries.org |
#4
|
|||
|
|||
Thats what I keep reading, to use a HAMMER carefully, hmmm I'll give it a try tomorrow
|
#5
|
||||
|
||||
I had to lie down across both seats and push up as hard as I can, but I have a long wingspan.
__________________
1985 500SL Euro w/ AMG bits 130k 1984 300SD Turbodiesel 192k 1980 240D Stick China 188k 2001 CLK55 AMG 101k 2007 S600 Biturbo 149k Overheated Project, IT'S ALIVE!!! |
#6
|
|||
|
|||
I used two rubber dead blow hammers, and a wife.
Had my wife hold mirror with one pin in the slot, then placed end of handle on the other side and whacked the head with the other hammer. took 3 tries and it snapped in. comes off easier than it goes back on. charlie
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
#7
|
|||
|
|||
still struggling to get that thing attached
__________________
White 1984 300TD-209K |
#8
|
|||
|
|||
As BENS LOVER said in post #2 and I laid out above in post#6, use a rubber dead blow hammer.
You have to hold the pin on one side against the hole where it snaps in, use the handle end of one dead blow tight against the base. use the second one, and whack it on the head. I have several dead blow hammers. think I used the 3 lb to whack it with. Just don`t want to hit the glass . I used my wife to hold it, don`t have one? grab the neighbors wife . and be careful. Charlie
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
Bookmarks |
|
|