![]() |
|
|
|
#1
|
|||
|
|||
Four to Five Speed Conversion
Hello, I am converting my 83 four speed manuel 240D to a five speed. These transmissions are almost nonexistant here in USA. So, I have inquired across the seas(and Canada) for a transmission. In the United Kingdom I have found several. My question is what other modification(components) will be required? I think the five speed transmission is longer and therefore driveshaft component will have to be changed as well. Does the same go for linkages? Finally as the British drive on the wrong side of the road, does this futher complicate the matter? I have searched the forum extensively and have been unable to find the exact nuts and bolts of this conversion but there is much disscussion. I would buy directly from Germany but searching in German is impossible for me. Can anyone recommend a German website(shop) that might have these parts forsale in English. The transmission will be rebuilt prior to instillation. Although I admire the quality of rebuilt Studggart components, I am reluctant to inquire at the dealership as my instincts tell me they will take me and my wallet for a ride. Where can I verify tansmission serial numbers and know I am buying is a five speed? Any assitance is greatly appreciated, regards, Miamirex
|
#2
|
||||
|
||||
As far as the shift linkage goes, the pattern stays the same between both left hand and right hand drive cars. The driveshaft will probably have to be shortened, and hopefully they are shipping the tailcone mount with your transmission, along with the shifter, linkage, driveshaft, and all associated hardware.
__________________
Nick ***** 2002 Sprinter 2500 140" High Roof ![]() |
#3
|
|||
|
|||
Babelfish at Altavista will translate German websites for you. I use it all the time for German ebay and www.mobile.de.
I owned a right hand drive Mercedes 307d (a van) and I don't think there was any difference at all in the transmission and linkages. I would think the driveshaft changes can be fairly easily accomplished here rather than paying for the shipping of a driveshaft from Europe. There are lots of Mercedes 'breakers' in the UK that should be able to provide you with parts. I have a couple of links to some if you are interested. One is called MercMan. I found them quite helpful when looking for parts for my 409d. Kerry
__________________
1977 300d 70k--sold 08 1985 300TD 185k+ 1984 307d 126k--sold 8/03 1985 409d 65k--sold 06 1984 300SD 315k--daughter's car 1979 300SD 122k--sold 2/11 1999 Fuso FG Expedition Camper 1993 GMC Sierra 6.5 TD 4x4 1982 Bluebird Wanderlodge CAT 3208--Sold 2/13 |
#4
|
|||
|
|||
5 Speed
miamirex,
If you've already a 4 speed in your car the swap to a five speed will be a snap. You must, however, get the shift knob assembly from inside the car and the shift linkages from under the car. If you do that everything will go in smoothly. If you can, get the short stub driveshaft from the donor car, then all that you'll have to do here is to have the driveshaft balanced when you put the front shaft into your old rear shaft. Good luck, you'll love it!!! Beni
__________________
www.reproduce100s.com |
#5
|
|||
|
|||
four to five speed conversion
That's great, thanks to all for the info, will be doing the conversion probably within a month, balancing the driveshaft? Never heard of that, but makes sence. Anybody in the USA rebuild manuel transmissions for Mercedes?
|
#6
|
|||
|
|||
Hey, thanks for this thread. Do you have any update on how the transmission swap went? I'm planning to start a swap to a manual from a 5-Speed manual out of a 1981 230 E from Germany and swapping that into my American 1984 300D. If anyone knows of any modifications other than the driveshaft that need to be done. Thanks for any help!
|
#7
|
||||
|
||||
If for any reason you need to remove the flywheel be sure to mark it so you can put it back in the same place on the crank.
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual. ![]() ..I also have a 427 Cobra replica with an aluminum chassis. |
#8
|
|||
|
|||
Quote:
__________________
1978 300D, 373,000km 617.912, 711.113 5 speed, 7.5mm superpump, HX30W turbo...many, many years in the making.... 1977 280> 300D - 500,000km+ (to be sold...) 1984 240TD>300TD 121,000 miles, *gone* 1977 250 parts car 1988 Toyota Corona 2.0D *gone* 1975 FJ45>HJ45 1981 200>240D (to be sold...) 1999 Hyundai Lantra 1.6 *gone* 1980s Lansing Bagnall FOER 5.2 Forklift (the Mk2 engine hoist) 2001 Holden Rodeo 4JB1T 2WD ![]() |
#9
|
|||
|
|||
The transmission that will fit your 617 engine is the 717400 look for this number on the transmission
|
#10
|
||||
|
||||
I heard Jooseppi Luna has a pair to sell.
__________________
CC: NSA All things are burning, know this and be released. 82 Benz 240 D, Kuan Yin 12 Ford Escape 4wd You're four times It's hard to more likely to concentrate on have an accident two things when you're on at the same time. a cell phone. www.kiva.org It's not like there's anything wrong with feeling good, is there? |
#11
|
||||
|
||||
Indeed! Well, kind of ~ one is sold pending payment, the other is
I do have a set of 717.400 shift rods that I am 90% sure are for the 240D, I'll try to check the measurements on those if someone is interested in them. Thanks for the shout-out, moon161 ![]()
__________________
"Senior Luna, your sense of humor is still loco... but we love it, anyway." -rickymay ____ "Your sense of humor is still loco... ![]() 1982 300SD -- 211k, Texas car, tranny issues ____ 1979 240D 4-speed 234k -- turbo and tuned IP, third world taxi hot rod ![]() 2 Samuel 12:13: "David said to Nathan, “I have sinned against the Lord.” And Nathan said to David, “The Lord also has put away your sin; you shall not die." |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|