|
|
|
#1
|
||||
|
||||
WTB: A/C manifold 1978-1980 300SD W116
Hey,
R-4 A/C compressor, GM-type Need the manifold that connects the rubber hoses to the compressor, mine is warped and won't seal. Thanks, -=-=-=Eddie Block
__________________
1978 300SD 149K miles silver-blue "Maxine" (mine!) 1979 300SD 318K miles red "Helga" (SOLD) 1980 300SD 321K miles yellow "Linda" (younger daughter's) 1980 300SD 148K miles blue (SOLD) 1980 300SD 153K miles green(parts car, SOLD) Yes, I have a W116 fetish :-) |
#2
|
|||
|
|||
I have one
I took 2 to the dump saturday I still have one on the car that I mean to pull some day How much is it worth then I will know if it is worth stopping other stuff to pull it I hope that makes sence. Dave S San Jose CA mattdave@pacbell.net PS if your local you can have it for free if you pull the AC pump.
|
#3
|
||||
|
||||
I'm in Austin, TX
To purchase a new one, it seems that the MB dealer is the only source...and they want $425 for the part! I found one at a local salvage yard, they wanted $40 for it, but it is warped in the same way as mine. It seems that if the center (the only) mounting bolt is over-torqued the mating surface bows making the flat surface rather convex, thus rendering the part unusable because it won't seal. If/when you remove the part, lay a straight edge along the mating surface and see if it's flat.
Thanks, -=-=-=Eddie
__________________
1978 300SD 149K miles silver-blue "Maxine" (mine!) 1979 300SD 318K miles red "Helga" (SOLD) 1980 300SD 321K miles yellow "Linda" (younger daughter's) 1980 300SD 148K miles blue (SOLD) 1980 300SD 153K miles green(parts car, SOLD) Yes, I have a W116 fetish :-) |
#4
|
|||
|
|||
I
I found I only sent one to the dump so I have one off the car I will pull the part later today how does $20 plus shipping sound.
Dave S |
#5
|
||||
|
||||
?
But, is it flat?
Any chance you could send me a pic of it so I can be sure it's the same part? What car did it come off of? I'm pretty sure the MB part number is 617-130-0157 but I don't know if that number is stamped on the part... I don't mean to sound picky or unappreciative, but I don't want to waste time/money and get my hopes up only to find that it won't work. Yes, Autumn is here but it's still 90 degrees in Central Texas! Thanks, -=-=-=Eddie
__________________
1978 300SD 149K miles silver-blue "Maxine" (mine!) 1979 300SD 318K miles red "Helga" (SOLD) 1980 300SD 321K miles yellow "Linda" (younger daughter's) 1980 300SD 148K miles blue (SOLD) 1980 300SD 153K miles green(parts car, SOLD) Yes, I have a W116 fetish :-) |
#6
|
|||
|
|||
it is flat
It is flat I just pulled it I was just going to ask for an email adress to send a picture too so you could see if it is the one you are looking for. I am 99 percent sure it is off a 1980 300sd but dont recall for sure there have been a few MBZ and I always yank the AC
MY email is mattdave@pacbell.net Dave S |
#7
|
|||
|
|||
wait
I was checking to see it was not warped in ward not if it had a very slight outward curve let me take off the o rings and check length wise.
|
#8
|
|||
|
|||
mesured it
If you put a flat edge across the outside edge there’s less than a thousands of an inch gap in the center so small as to be insignificant
|
Bookmarks |
|
|