FS: 1984 300TD amercian wagon part out - Page 4 - PeachParts Mercedes-Benz Forum

colincoon · #46 06-23-2012, 11:31 PM

PM'd about the diff.

gregg · #47 08-13-2012, 10:23 PM

I am looking for the the rear plastic trim for window switch in palomino. Must have both tabs intact with no cracks. Thanks

joshuajeeper · #48 08-15-2012, 12:14 PM

I'm looking for the metal retainers that secure the top of the rear hydraulic shocks to the body that the bolt goes through. Part number 123-326-06-67. I need these as soon as possible!

NCfriend · #49 08-15-2012, 05:14 PM

gregg: I will double check condition soon, i am stuck with a 13 hr work day today! But I know I have a pair, just want to confirm all tabs are good for you. PM a list of anything else you need

joshuajeeper: I hadn't forgotten that request, but removing SLS struts was low on the list. The rear is jacked up and accumulators sold.
Can you send me a DIY for removing these?
that always speeds things up

joshuajeeper · #50 08-15-2012, 07:57 PM

You remove the rear cargo covering on the floor and you'll see the bolt and washer for the rear shocks. In front of the bolts, you will see an access cover (plastic). Remove the covers and the hoses to the struts are there. Remove the hoses and then you can remove the upper bolt. To remove the struts from that point, all you have to do is pull the two bottom bolts, and they come right out. Be careful before removing the upper bolts if you don't want to rip the rear brake hoses. The rear shocks hold up the trailing arms and if you take the upper bolt out, the suspension will drop down and over extend the brake hoses.

I need 5i in the picture.

Thanks

NCfriend · #51 11-14-2012, 04:23 PM

A little bump!

I am headed up to DC area next week, from Greensboro NC with a trailer full of parts!
Can deliver along route with many w123 goodies to share...

NCfriend · #52 11-18-2012, 06:28 PM

Gotta bump this up one more time;
I am pulling parts and loading the trailer tomorrow!!

Following mostly HWY 29, from Greensboro NC to Frederick MD

Anybody need some w123 parts dropped off? Got an extra turkey leg for lunch

ytmtnman · #53 11-26-2012, 01:22 PM

pm sent

NCfriend · #54 01-30-2013, 11:58 AM

I am bumping this up guys.

Just sold the factory antenna, but have tons of parts on this wagon and other w123 donors too.
Plus preparing for a cross-country road trip (April) that could offer delivery of larger parts!
NC -> Cali along I-40
Cali-> Maryland through the mid-west

Raptelan · #55 01-30-2013, 01:21 PM

Did you sell the manual tranny already?

NCfriend · #56 01-30-2013, 10:27 PM

1984 euro wagon? NO, but eventually on the car will be on the market

Separate trans from the euro sedan I parted out, YES it is in Disgo's wagon now

WTT: Might be looking to trade in parts for an early model brake master cylinder, the kind with a pressure switch on the side for brake lights and one one electrical plug on top! I have good ones from newer models that I can swap anyone or other w123 parts

NCfriend · #57 01-31-2013, 12:17 PM

Just to help answerthe popular question: the crossbars are SOLD
Same for all my rear hatch interior handles

I do have rear wiper motors, all the hardware for a cargo cover (but no cover), some wagon interior pieces in palomino-black-and blue colors!

NCfriend · #58 03-31-2013, 04:30 PM

The Bunny told me this morning:
"Gotta Bump It"

Wanted to stress that I am traveling across the country from NC to San Fran along I-40 and back again along I-80/90 to MD

I can deliver!! w123 parts from my squirreled stock piles nearby to these routes

Start the PM requests please and help me fund the trip
FREE shipping

A few tasters: I have round style euro lights, extra 1-piece front euro bumper, tool kits, 1st aid kits, a rebuilt 240 diff in hand and tons more just good stuff

NC-Diesel · #59 03-31-2013, 11:04 PM

How about 2 good fenders? I bent up one on my 1981 trying to get it off passenger side and I got a 78 that had accident damage to the drivers fender. May be easier to replace then to try to pop this dent. IN dire need of a 240 Flywheel for a manual and a manual drive shaft for a 240. Otherwise I may have to consider buying a gasser 280E to put this 4 speed in since I have the flywheel, drive shaft, etc!

Renntag · #60 04-01-2013, 04:17 PM

Is there a list of remaining parts?

Have the rear door straps by any chance?
Cowl vents?
Left rear 1/4 panel body molding.
I have a list of stuff.