considering buying a Baum Tools brand spring compressor for $300.

I know i can get an chinese-made Ebay special for about $160 but I don't mind paying a little extra for the quality difference if there is any.

Looking at that front suspension spring coming off the wrong way gives me the shivers.

Question--is that brand pretty good? the retail for the spring compressor is $695

__________________
Ben
1987 190d 2.5Turbo

I usually prefer to buy a better quality of tool if I am going to use and reuse and reuse. I don't like to buy a good quality tool just to use it once and probably never again. This is one of those cases that I think is best farmed out so you don't have another piece of metal in the garage sitting and gathering dust.

__________________
01 Ford Excursion Powerstroke
99 E300 Turbodiesel
91 Vette with 383 motor
05 Polaris Sportsman 800 EFI
06 Polaris Sportsman 500 EFI
03 SeaDoo GTX SC Red
03 SeaDoo GTX SC Yellow
04 Tailgator 21 ft Toy Hauler
11 Harley Davidson 883 SuperLow

If you only need it one time, why not rent it from one of the members?

Or, if you have a good floor jack and good jack stands, you can do without.
Get the car high enough to allow the control arm to fully lower. Then put the floor jack in place and remove the hardware that holds the arm. Then slowly lower the arm till no tension is left. Worked good for me on my W124.

By the time the arm is fully lowered there is not much tension left. Easily controlled with the floor jack the rest of the way.

I bought a number of MB-specific hand tools from Baum when I bought my MB 16 yrs. ago.

First rate in my opinion, but as stated above, "made in China" might work if needed only once. If you're going to go low, look at Harbor Freight. Their quality has improved.

__________________
Mike Murrell
1991 300-SEL - Model 126
M103 - SOHC
"Fräulein"

I had a lesser version break one of my fingers, get the quality tool.

__________________

90 300TE 4-M
Turbo 103, T3/T04E 50 trim
T04B cover .60 AR
Stage 3 turbine .63 AR
A2W I/C, 40 LB/HR
MS2E, 60-2 Direct Coil Control
3" Exh, AEM W/B O2
Underdrive Alt. and P/S Pulleys,
Vented Rear Discs, .034 Booster.
3.07 diffs 1st Gear Start

90 300CE 104.980
Milled & ported head, 10.3:1 compression
197° intake cam w/20° advancer
Tuned CIS ECU
4° ignition advance
PCS TCM2000, built 722.6
600W networked suction fan
Sportline sway bars
V8 rear subframe, Quaife ATB 3.06 diff

I agree with Murrell. While I don't frequent Harbor Freight on a regular basis I do shop there now and again.

Their quality has come up over the last twenty years, and some of their tools are close to top quality.

But perhaps you could shop Ebay for such a tool, use it, and then sell it again. I know a Video Producer who uses this method to secure equipment, and he tells me it is not only cheaper than renting but he sometimes turns a small profit during the resell.

This is one item I would not cheap out on. The possible consequences of it's failure are too severe. The good tool is probably forged steel. The lesser tool may not be. Coil springs can kill.

For the amount of times an average owner uses one rent it.

Wouldn't it be easier to farm this one out so you don't have the hassle of reselling it or waiting for the right priced one to come along or keep a tool you will probably never use again? For a commercial application perhaps but toils get expensive for a one time use.

__________________
01 Ford Excursion Powerstroke
99 E300 Turbodiesel
91 Vette with 383 motor
05 Polaris Sportsman 800 EFI
06 Polaris Sportsman 500 EFI
03 SeaDoo GTX SC Red
03 SeaDoo GTX SC Yellow
04 Tailgator 21 ft Toy Hauler
11 Harley Davidson 883 SuperLow

I have several baum tools. but they aren't the baum tools you might be thinking
of.

__________________
For the Saved, this world is the worst it will ever get.
For the unSaved, this world is the best it will ever get.

Clk's Ebay Stuff BUY SOMETHING NOW!!!

Don't think he is looking to borrow your BUM TOOLS.

__________________
01 Ford Excursion Powerstroke
99 E300 Turbodiesel
91 Vette with 383 motor
05 Polaris Sportsman 800 EFI
06 Polaris Sportsman 500 EFI
03 SeaDoo GTX SC Red
03 SeaDoo GTX SC Yellow
04 Tailgator 21 ft Toy Hauler
11 Harley Davidson 883 SuperLow

NO!!!! Baum® Tools.

__________________
For the Saved, this world is the worst it will ever get.
For the unSaved, this world is the best it will ever get.

Clk's Ebay Stuff BUY SOMETHING NOW!!!

Have you considered hiring the job out to a professional front end suspension specialist shop? Either that or make sure both your life and health insurance policies are paid up in case you experience an accident. As for myself, I'd rather hire out a job like that than possibly experience a life changing injury. Pay someone else to step into harms way......

The old saying, there is the "cost" and then there is the "price". Which one do you want to pay????

Thee Baum® tools I have are specialty tools for the Baum paper folding machine.

__________________
For the Saved, this world is the worst it will ever get.
For the unSaved, this world is the best it will ever get.

Clk's Ebay Stuff BUY SOMETHING NOW!!!

Before buying I would contact Baum Tools and ask them where the Spring Compressor is Made.

__________________
84 300D, 82 Volvo 244Gl Diesel

On eBay
Mercedes Klann coil spring compressor tool - NEW! W123 W124 W201 W202 W203 R129

This spring compressor set is made by Klann for SPX Tools. It is the real deal, made in Germany spring compressor, not a cheap Taiwan copy. It is identical to the Klann KL-0025 in every way except the name stamped on the side. These are brand new, never used!

$599 with free shipping
Mercedes Klann Coil Spring Compressor Tool New W123 W124 W201 W202 W203 R129 | eBay

__________________
84 300D, 82 Volvo 244Gl Diesel