|
|
|
|
|
|
|
#1
09-13-2006, 06:05 AM
|
|||
|
|||
|
E200 Headlining Is Drooping - Any Quick Fixes?
For the past few days, the headlining of my 1997 E200 W210 is suddenly drooping down across the full width of the front of the car, above the driver and passenger seats. It seems to be sagging by nearly 2 inches and is continually dragging in my hair as I am driving. If I push it up and smooth it along the underside of the car roof, it stays put for a few minutes, but gradually droops down again. Other than not sticking where it should, the material looks in good condition and is not marked or damaged.
Does anyone know of any quick fixes to stick this headlining back up, or is it likely to mean an expensive shop repair job? Any help would be appreciated. By the way, I am in Singapore, in case that makes a difference. 
|
|
#2
09-13-2006, 11:16 AM
|
||||
|
||||
|
3M headliner adhessive
There are products like the one I mentioned above. I tried it once on a Lincoln with the same problem. Unfortunately, it was a VERY temp. fix, as the real problem was that the foam it was attached to had deteriorated to the point that it, and not the adhessive was the weak spot. I had to replace the entire headliner.
Good luck with yours. I haven't tried it on a Benz, so don't know if it is constructed in the same way.
__________________
" We have nothing to fear but the main stream media itself . . . ."- Adapted from Franklin D Roosevelt for the 21st century  OBK #55 1998 Lincoln Continental - Sold Max 1984 300TD 285,000 miles - Sold The Dee8gonator 1987 560SEC 196,000 miles - Sold Orgasmatron - 2006 CLS500 90,000 miles 2002 C320 Wagon 122,000 miles 2016 AMG GTS 12,000 miles
|
|
#3
09-13-2006, 09:44 PM
|
|||
|
|||
|
Well if the material is mounted on foam I think it will be bad news. Foam seems to just rot away in the Singapore humidity and crumbles into small particles. Looks like I'll have to try the MB dealer.
Thanks for the reply.
|
|
#4
09-14-2006, 10:53 AM
|
||||
|
||||
|
Hi there! Same issue.
93 300E. Headliner has been sagging for years...more pertinent issues to fix, so I've lived with it. Tried the 3M spray adhesive...worked for about a minute. The deteriorated foam won't allow proper adhesion. Only a replacement will do. Texas summers probably accelerated the breakdown of the foam...
__________________
2009 ML350 (106K) - Family vehicle 2001 CLK430 Cabriolet (80K) - Wife's car 2005 BMW 645CI (138K) - My daily driver 2016 Mustang (32K) - Daughter's car
|
|
#5
09-14-2006, 12:13 PM
|
|||
|
|||
|
Also did not work...
Hi,
I have a 95 e320 sedan and the headliner in my car is a hard surface in the front and fabric on the sides and back; the fabric droops. I contacted a headliner person online who answered peoples' questions, and asked if I could use some sort of brad in a couple of places as mine was not drooping all that bad (I have replaced about 3 headliners on other cars and was trying to avoid it). He said that thumbtacks would actually work really well. I actually PAINTED some thumbtacks to match and tried this; they did not even stay in for a second. So, cross that off your list if you were contemplating it. I am still wondering whether you could drill a hole in the hard surface (behind the foam), and place a couple of plastic brads through the fabric and that hole. This could look very jerry rigged but in cases where the liner does not droop too bad I wonder if it might still work. I can only speculate...
|
|
#6
09-14-2006, 12:17 PM
|
|||
|
|||
|
Hypodermic needle w/CA [ Crazy Glue ]
|
 |
| Bookmarks |
|
|
Hybrid Mode
