|
|
|
#1
|
|||
|
|||
1993 mirror switch replacment
Where can I fint a digram on how to replace it ? and how hard it is ?
an ebay member have a brand new one for $46 shipped is that a good deal ?
__________________
2003 GX470 1998 E300 3.0TD 2002 Dodge 2500 4x4 cummins 1998 Dodge 3500 5 speed Cummins |
#2
|
|||
|
|||
Simply "pops" into the wood trim.
Most of the time you wouldn't need to wood trim at all.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#3
|
|||
|
|||
Hardest part is getting the console wood out to replace the switch.
Process is long and detailed. Plenty of opportunity for damage to existing items. Suggest you purchase an AllDataDIY subscription for about $20. There are detailed instructions on how to get the console wood out so you can change the switch. |
#4
|
|||
|
|||
#5
|
||||
|
||||
Our Sponsor
All Parts Express (top of page Buy Parts "Pull Down" menu) has your switch
6 bucks cheaper. [picture may not match your actual switch]
__________________
'84 300SD sold 124.128 |
#6
|
||||
|
||||
I replaced mine (W124) years ago when the knob broke off the shaft. Don't remember the process being all that difficult.
As said, removal of the console is necessary, but I had been in there before.
__________________
2009 ML350 (106K) - Family vehicle 2001 CLK430 Cabriolet (80K) - Wife's car 2005 BMW 645CI (138K) - My daily driver 2016 Mustang (32K) - Daughter's car |
#7
|
|||
|
|||
i got the ashtray surrond loose ( it wont come out ) and the front of the console pulled up but cant figure out how to get it off all together
I cant see any screws any where is every thing clipped in ? HELP no online manual ? been looking and cant find it unless i am looking in the wrong place
__________________
2003 GX470 1998 E300 3.0TD 2002 Dodge 2500 4x4 cummins 1998 Dodge 3500 5 speed Cummins |
#8
|
||||
|
||||
To remove Horizontal Console wood
Pull up the front of the small rectangular piece of carpet under Driver's Armrest
[The "Console Tray"].There is one Phillips head screw,remove it. There is a Black plastic surround that fits the inner diameter (Rectangular) of the Shifter area Gently wriggle it up and off. Place shifter lever in Neutral. Gently, ever so gently Pivot the wood piece Upwards from the rear... There are two plastic hooks in the front edge of the wooden piece... [If you break them they are available as replacement parts,BUT you'll never get the staples that affix them to the wooden console piece, OUT!] So what you're doing is moving the rear of the wood piece from horizontal to vertical,Whilst the front of the wooden piece remains down. The Mirror switch is a "Friction Fit" into it's plug which is attached to the Console...You just wiggle it upwards.
__________________
'84 300SD sold 124.128 |
#9
|
|||
|
|||
As I indicated before, loosen the screw on the ashtray lid after removing the ash tray insert, slide it upward and remove. Then locate the two lateral (sideways) torx that hold the upper and lower panels together and remove them. Once they are removed and the shift trim is removed by pulling up on it, the panel can be raised on the ash tray side, and then pulled slightly forward to release the catch on the arm rest side. The two phillips screws that you see looking straight down hold the upper console panel.
|
Bookmarks |
|
|