|
|
|
#1
|
|||
|
|||
Need rotor specs for 2000 E320
Hello,
I'm new to this forum. I'd be grateful if someone could provide both new and minimum (thickness) for front and rear rotors. I have model 210.065, 2000 E320. Also, your recommendations for the best place to purchase, and favorable brands would be appreciated. I don't have the money to pay for the very best right now, but would like to put good pads and rotors on. So, best value for the dollar. I've heard Zimmerman rotors with Akebono's are a good set up. I have single pin in the rear. Thank you in advance for your help! Brent |
#2
|
||||
|
||||
Your specs are imprinted on the hub of the rotor. Something like 25.4 for the front iirc.
__________________
1980 500SE/AMG Euro 1981 500SEL Euro 1982 380SEL 1983 300TD 1983 500SEC/AMG Euro 1984 500SEC 1984 300TD Euro 1986 190E 2.3-16 1986 190E 2.3 1987 300D 1997 C36 AMG 2003 C320T 4matic past: 1969 280SE 4.5 | 1978 240D | 1978 300D | 1981 300SD | 1981 300SD | 1982 300CD | 1983 300CD | 1983 300SD | 1983 380SEC | 1984 300D | 1984 300D | 1984 300TD | 1984 500SEL | 1984 300SD | 1985 300D | 1986 300E | 1986 560SEL | 1986 560SEL/Carat | 1987 560SEC | 1991 300D 2.5 | 2006 R350 |
#3
|
|||
|
|||
Front rotors (210-421-22-12) on THAT car have a 25.4mm minimun & would be 28mm thick when new.
Rears (210-423-06-12) have a 8.3mm minimun & are 10mm new.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#4
|
|||
|
|||
x2
__________________
1986 300SDL, 211K,Dealership serviced its whole life 1991 190E 2.6(120k) 1983 300D(300k) 1977 300D(211k) |
#5
|
|||
|
|||
Thank you gentleman. I appreciate the information. Hey M.B. Doc, the numbers you have listed after front and rear rotors, are they the actual part numbers needed for my vehicle. Please pardon my ignorance.
I'm not a mechanic but have been doing many DIY's out of necessity. I actually enjoy it, but still have a lot to learn! Thanks again. Any opinions on rotor and pad set up? Brent |
#6
|
|||
|
|||
Unless you buy OE from dealer?? Use Zimmermann rotors & Textar pads (ceramic)
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#7
|
|||
|
|||
No, I try not to use dealer, their too pricey! Thanks MB Doc. I appreciate the information.
Brent |
Bookmarks |
|
|