|
|
|
#1
|
||||
|
||||
How to remove window tint???
Dose anyone know how to remove window tint
__________________
Current Garage 2008 Mercedes GL320 CDI 188k mi Repair/Work in progress 1994 S350 160k mi Garage Queen & prepping for repairs 2005 E320 CDI 203k mi Healthy & Daily Driver 1994 S350 357k mi Retried as parts car 1984 300TD 214k mi Blown OM617 Poss OM603 Swap?? Sold 1987 300SDL 200K+ 1994 S320 181K mi 2008 E320 Bluetec 127k mi 1999 S420 130K mi 1980 240D 360k mi 15+ Others that has come, stay and gone GONE, BUT NOT FORGOTTEN 1995 E320 SE 220k mi 1984 300SD 350k mi |
#2
|
||||
|
||||
Step 1:
To over come separation between layers you must soften the adhesive so that both layers peel at the same time. This is very important, if you peel the just the top layer, you may as well just use razor blades as there is no way to peel the second layer off without picking at it for a few hours. You MUST try to peel both layers at once. NOTE: You are more than likely to damage one or more of your defroster lines, when this happens, the cut line will not work anymore. Some cars have radio antennas mounted alongside the defrosters made of the same material. If you damage these, your radio antenna will not work! Be careful! Taking it to a tint shop to be done greatly increases the odds of saving the lines, but even a tint shop can not promise to save your lines, sometimes the film is just to far gone. Step 2: First, clear the window of any obstructions, like the brake light, speaker covers etc. Step 3: Next cut open the garbage bag so that it will be big enough to cover the entire window. Spray some water on the outside of the back window and the lay plastic bag over the glass. Cut away excess plastic so that it is now roughly the same shape as the glass. Step 4: Next, lay a tarp over rear deck and seat, spray ammonia liberally on the inside of the back window. (Ammonia is very strong, I suggest you hold your breath during this step) and cover ammonia soaked tint with the plastic bag so that it won't evaporate. Step 5: Park the car with rear window facing the sun for about an hour. The film should now be ready to peel. Step 6: When you are ready to start peeling, leave the plastic in place so the ammonia wont dry. Get the peeling started with a razor blade in a corner where there are no defroster lines. Try to peel film off in one piece. If the ammonia dries as you peel, the glue will get hard again, so spray a bit of ammonia on the area as you peel. Step 7: Once the film is peeled you will need to scrub the adhesive off with ammonia and fine 0000 steel wool. Mop up scrubbed areas with paper towels before they dry. Finish up with window cleaner and paper towels. Courtesy of the TINT DUDE
__________________
BENZ THERE DONE THAThttp://www.peachparts.com/shopforum/...c/progress.gif 15 VW Passat TDI 00 E420 98 E300 DT 97 E420 Donor Car - NEED PARTS? PM ME! 97 S500 97 E300D 86 Holden Jackaroo Turbo D 86 300SDL (o\|/o) |
#3
|
||||
|
||||
Geezz that is some long steps. Yeah the PO, tried to peel out the rear window tint hastly with a blade and they damaged the window defroster!!!
__________________
Current Garage 2008 Mercedes GL320 CDI 188k mi Repair/Work in progress 1994 S350 160k mi Garage Queen & prepping for repairs 2005 E320 CDI 203k mi Healthy & Daily Driver 1994 S350 357k mi Retried as parts car 1984 300TD 214k mi Blown OM617 Poss OM603 Swap?? Sold 1987 300SDL 200K+ 1994 S320 181K mi 2008 E320 Bluetec 127k mi 1999 S420 130K mi 1980 240D 360k mi 15+ Others that has come, stay and gone GONE, BUT NOT FORGOTTEN 1995 E320 SE 220k mi 1984 300SD 350k mi |
#4
|
||||
|
||||
Quote:
There is some liquid you can buy to paint new lines on the glass. I forget what it is called. Probably 'Defroster Repair'
__________________
"I have no convictions ... I blow with the wind, and the prevailing wind happens to be from Vichy" Current Monika '74 450 SL BrownHilda '79 280SL FoxyCleopatra '99 Chevy Suburban Scarlett 2014 Jeep Cherokee Krystal 2004 Volvo S60 Gone '74 Jeep CJ5 '97 Jeep ZJ Laredo Rudolf ‘86 300SDL Bruno '81 300SD Fritzi '84 BMW '92 Subaru '96 Impala SS '71 Buick GS conv '67 GTO conv '63 Corvair conv '57 Nomad |
#5
|
||||
|
||||
3m general purpose adhesive remover
When the tint film pulls away from the Adhesive layer (Some of it will)
This 3m product on a clean white rag will remove the adhesive nicely! [Do Not SCRUB HARD at the defroster lines!] ALSO used when removing the leftover Hood Pad Adhesive on the underside of the Hood.
__________________
'84 300SD sold 124.128 |
Bookmarks |
|
|