Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 01-22-2006, 07:52 PM
1992 300d 2.5 175k
 
Join Date: Jan 2006
Location: kauai hawaii
Posts: 14
Question 92 300d 2.5l heating problem

went for a ride in the mountains about 5000' elevation and had an overheat. my brother in-law wasn't watching the temperture and the car died. towed the car home and it started up. one injector made nailing sounds and the temp rises to the red.

i flushed out the cooling system and changed the stat. i changed all the injectors. the car now runs really nice with more power. however, the temp runs up to around 120 near the red and my heater blows very cold ac air. i switch the heat to the full hot position and only ice cold air.

i am gonna check on the mono valve... i hear a gurgling sound in the heater core when i turn the engine off.

anyone got any ideas on whats wrong?
Reply With Quote
  #2  
Old 01-22-2006, 10:09 PM
dieselbeagel's Avatar
Registered User
 
Join Date: Nov 2003
Location: California
Posts: 334
Did u check the coolant level ? Is the radiator leaking ?

The heating circuit also contains the thermostat. Check the hoses, u could have one with a slow leak.

R u burning any oil ? Oil leaks that needs attention.

Let us know what u find out.
Reply With Quote
  #3  
Old 01-22-2006, 10:47 PM
1992 300d 2.5 175k
 
Join Date: Jan 2006
Location: kauai hawaii
Posts: 14
my oil level is normal. no oil leaks although one of my injectors is leaking air. i removed the injector and the heat shield and checked it out. the heat shield is in with the tapered side down. i wrenched it back in at 100 ft lbs.

the injector still makes a tapping sound and i can feel air comming from it. the performance is great however.

i checked the stat and it is in the right way --- you cant put it in the other way because the housing on the hose side is too shallow. also the stat can only seat at a certain placement because of a notch in the stat that accepts the housing. the stat is new and i dont know if wahler is any good --it cost $30 and i am guessing its a good one.

the radiator feels warm all over but the hose going in at the top gets very hot and feels full of pressure. the lower hose is not collapsed and it is not as hot as the top hose.

i dont have any coolant leaks as my garage floor is dry over night.

i noticed that the temp decreases a bit when parked and i rev it. i am wondering if the water pump is lame. i hate to go buy a new one and replace it only to find out that it isnt the problem. is there a way to determine if the pump is working properly?

my heater doesnt work but i can live with that --- it doesnt get cold here in hawaii. but it seems the heater went out the same time as the overheating incident in the mountains.
Reply With Quote
  #4  
Old 01-22-2006, 11:13 PM
dieselbeagel's Avatar
Registered User
 
Join Date: Nov 2003
Location: California
Posts: 334
The water pump may be the problem. Do u see any coolant in the pump peep hole?

I believe the 602's do have small black hose at the bottom of the pump that does sometimes drain some coolant. Do not mistake that for a leak.

Another guess - air in cooling system ???
Reply With Quote
  #5  
Old 01-23-2006, 02:23 AM
1992 300d 2.5 175k
 
Join Date: Jan 2006
Location: kauai hawaii
Posts: 14
i will remove the top radiator hose and fill it and see what happens...does the air work its way out on its own? should the overflow tank be full to the top? i filled it to the top and it overflows out the drain hose. The water sets about an inch from the top when it cools.

i will check out the water pump tomorrow ... is it a big job to change? looks like a lot of work getting in there. looks like the radiator would have to come out to do it.

and thanks man
Reply With Quote
  #6  
Old 01-23-2006, 09:44 AM
dieselbeagel's Avatar
Registered User
 
Join Date: Nov 2003
Location: California
Posts: 334
The water in the overflow tank should be about the height of the middle seam.

Look at the bottle and there should be an arrow that shows where the coolant level should be when cold.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 02:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page