DeliveryValve had the idea and did the research on using the Baldwin fuel/water separator BF7591-D (with a drain) in place of the stock 10 Micron secondary fuel filter.The Baldwin BF7591-D according to the Baldwin rep is rated between 1 or 2 microns and it is a fuel/water separator in which includes a drain. It fits perfectly on the base with no grinding at all, but needs a M16x1.5 filter bolt. He also provided all of the material and funds for the project.

DeliveryValve’s idea is in post #11 and my idea is in post #5
Lowest Fuel Filter Micron Rating
2 problems were that the BF7591-D has 16mmx1.5 threads and the stock filter has 14mmx1.5 which meant that a larger 16mm bolt would be needed and that the Filter Housing would need to be threaded for the 16mm bolt. (The sealing of the central bolt to the filter housing would be similar to the older style central bolt with the crush washer at the top.)
My part of the project was to thread the filter housing and drill holes through the center and across the provided 16 mm bolt.
The only real problem that came up was that the Bolt Head was too large for me to slip it behind the Lathe Chuck Jaws and would not allow the Lathe Chuck Jaws to close on the threaded shaft of the bolt. I had to swap ends and drill through the head of the bolt which meant that I had to drill the whole length of the bolt; which I had not intended to do. The reason for not wanting to drill the length of the bolt is that chips can build up inside and you can snap a drill off. This meant drilling a little and pulling the drill all the way out; clearing the chips repeating the same process over and over until the hole is safely drilled completely through the length of the bolt.
Now I had an unintended hole in the head of the bolt to plug up. I decided to tap it for ¼”x28 threads and turn it into a bolt you could use to bleed the air out of the filter when you change filters; instead of having to loosen a banjo bolt.
When I cross drilled the bolt I drilled through both sides of the bolt so if the holes look small in the Pics remember there is 2 holes instead of the 1 bigger hole that the stock central bolt has.
The first Pic is one I copied from Delivery valve the rest I took.
Depending on what is under the filter (may be different with different car/engine models) an adapter plate may need to be made to move the filter 1” or so away so that there is clearance under the filter for the filter to be changed.

__________________
84 300D, 82 Volvo 244Gl Diesel

The modified bolt with the air bleed at the top is on the left.

Finish product.

I also sent a drill plate incase the filter needed to be moved away from the casting web that is below the filter but I am waiting for DeliveryValve to tell me if you need this or not. He will be installing it soon. (I already have that big white filter on my car it required a little grinding of the filter housing and needed the drilled plate to move it away so that the filter could be changed.)

__________________
84 300D, 82 Volvo 244Gl Diesel

I will be installing this setup hopefully later this upcoming week. I really like the bleeder screw setup because I can use my Mityvac to draw the air out and fuel into the filter. It was a good problem for Diesel911 to have.

Stay tuned!

__________________
1983 123.133 California
- GreaseCar Veg System

Looks great. I'll definitely be doing this some day to get rid of my stand-alone water separator.

You should be able to get an M16x1.5 banjo bolt at most any hydraulic/hose shop.

I would like to do this mod as well. You should sell a "conversion kit"

For some reason I thought that the bolt hole in the filter head was not threaded and the bolt just passed through into the filter.

__________________
1979 240D- 316K miles - VGT Turbo, Intercooler, Stick Shift, Many Other Mods - Daily Driver

1982 300SD - 232K miles - Wife's Daily Driver

1986 560SL - Wife's red speed machine

Nope, it passes through the housing and the filter screws onto it.

Thats why we call it the bolt-on filter instead of screw-on.

I tried. But my local hydraulic/hose shops around here don't have any.

As Lance stated, it is not threaded. I had Diesel911 put M16X1.5 threads on the filter mount so that I can convert the filter to a screw-on type. I also thought because the center hole of the filter mount tapers up to a larger size in diameter then the M16 bolt near the top of the mount, by having threads on the bottom would stabilize the banjo bolt for a better seal on the bolt head. I am planning on using gas rated Teflon tape on the threads to seal the banjo.

In other notes, as stated the in links earlier Diesel911 is using a CAT 1R-0750 two micron filter mod on his car. He made a threaded adapter that is 1"-14 to use that filter. I think he stated that the true CAT filter is skinny enough that there is no grinding modification of the filter mount to install as opposed to the WIX 3528 version he originally used. But I'll let him talk about his version of this mod if he chooses for later in this thread.

__________________
1983 123.133 California
- GreaseCar Veg System

The original bolt/housing is not threaded part of this is because the origional bolt has an O-ring to seal it down in that area so the space around where the bolt sticks out is irrelvant as it is sealed further up by the O-ring.
On our mod in order to use a similar O-ring set up would have required machining a whole new central filter bolt with properly sized grooves in it for the O-rings and the housing. To invent bolt from scratch would have taken way too much time.
Using a regular bolt 16mm simplified things.
We thought threading the housing was the simplest way to go.
I am open to ideas; one of the reasons for this Thread is that we get ideas from other members. Maybe all we needed was a bigger hole with no threads but you will need to find something to seal that area or the fuel will not go into the filter in will bypass and go between the bolt and filter housing.
What we did was DeliveryValves idea as he wanted to use that specific filter with a bottom drain. I chose a different path and had to make a threaded adapter for my choice of filter and a drilled plate to move the filter out further so the longer filter would have room to change.


Due to a fatter filter about 1/6 of metal had to come off the areas shown in the photo

and I also had to lengthen the fuel line that returns from the fuel injection pump due to the banjo fitting having to be rotated in a different direction to clear the filter top.
I used the NAPA version (3528) of a CAT filter. Since then I have recieved a real CAT filter 1R-0750 and the top of this filter has a smaller outside diameter than the NAPA one and I beieve it will require no metal removeal on the filter housing. Another bonus is CAT claims an absolut 2 micron filtration while the NAPA filter is only 2 Nominal Micron filtrations.

__________________
84 300D, 82 Volvo 244Gl Diesel

Okay. I have 3 kits available that include modified base, extension plate, metric hardware, new crush washers and M16x1.5 banjo bolt. For extra I can include a BF7591-D filter. Price is TBA as soon as I find a banjo bolt long enough (The one in the picture is about 1/2" too short to work).

The bleeder screw is unnecessary. There is already a bleeder hole in the filter base that bleeds air from the filter to the return side. Its under the banjo bolt where the two return lines merge into the cigar hose. (see pictures) All you have to do is pump the primer and it will bleed itself, even if you don't fill the filter first.

Attached Thumbnails

     

Why did the filter housing need to be tapped? Function as the o-ring?

__________________
For Sale: 1982 MB 300TD
1995 Chevrolet Suburban 6.5TD

Sold: 1980 IH Scout Traveler- Nissan SD33T Diesel

Why do this modification?... Isn't this over-kill?

What size micron of particles will safely flow through the injectors?

Is the factory recommended Mercedes filter not fine enough?

__________________

"Our Lady of Blessed Acceleration...
don't Fail Us Now"

Baja nailed it. Going through the injectors is not the issue, its protecting the precision injection pump from damage.

It also has the bonus of being larger which means it will last longer. That can make the mod pay for itself since the filter is about the same price as the stock one.

This looks like a really cool mod. Looks like it will fit on my 85 TD. I
love the concept of the 2 mic filter and the "easy bleed" screw. If it
comes in at a "reasonable" cost I'll take a kit,thanks

__________________
85 300TD FED-Daily
84 300SD-Wife's
86 XJS-Sunday
66 GMC-Work- Given to my stepson
83 BMW Airhead- Given to my stepson

It's a combination of finer filtration and the addition of a water trap. To me, both of these points equate to longevity of the injectors AND the PUMP (particles are abrasive).

__________________
For Sale: 1982 MB 300TD
1995 Chevrolet Suburban 6.5TD

Sold: 1980 IH Scout Traveler- Nissan SD33T Diesel

Bookmarking thread.

__________________
'06 E320 CDI
'17 Corvette Stingray Vert