|
|
|
#61
|
|||
|
|||
Quote:
__________________
You can't always get what you want, but if you try sometime you just might find you get what you need. |
#62
|
|||
|
|||
I just came across this tread, I'm about to do the same swap with two of my 300Ds in about a week, very interested in seeing how this turns out for you!
Was the pilot bearing hard to source on eBay? I just picked up a solid 84 300D non turbo euro with a manual trans that was heading to the scrap yard, and want to drop an engine from an automatic car into it. Best of luck, looks like in a few days you'll have yourself a nice car this summer |
#63
|
|||
|
|||
Yep! I'm excited for it. I just ordered a pilot bearing for a 240d on ebay. It was like $9 bucks. Are you going to make a thread for your swaps?
|
#64
|
|||
|
|||
Have you looked in here for any of your Clutch related parts?
1982 Mercedes-Benz 240D Sedan - Clutch & Flywheel - Page 1 Charlie
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
#65
|
|||
|
|||
While I'm waiting for my pilot bearing to show up, I tried to start it today, without the tranny. Turn the key, nothing. I forgot about the neutral safety switch! How do I rewire that? What do I need to do?
|
#66
|
|||
|
|||
The Neutral Safety Switch and reverse light switch harness goes through a grommet in the transmission tunnel and up to a 4-prong plug on the left side of the center console near where the driver's right knee would be.
The cleanest fix is to get the reverse light harness from a manual 240d. It connects from the shifter to this 4-prong plug to turn on the reverse lights and short the NSS circuit. If you don't have this or can't get it from the junkyard, you can connect the violet wires to make the starter circuit work. -Dan
__________________
1976 w115 300D 4-speed conversion!! 1985 w123 300TD 4-speed conversion!! Non-Mercedes old stuff: 1941 Buick Special (Straight 8!) 1946 Luscombe 8a 1947 Willys CJ2a 1950 Chevrolet 4400 dump truck 1954 Chevrolet 3600 3/4 ton 1954 Cessna 195B 1955 John Deere model 40 1991 Ford Taurus SHO 2013 Jetta SportWagen TDI 6-speed (I sold out... |
#67
|
|||
|
|||
What is the torque for the flywheel??
|
#68
|
|||
|
|||
I tried to install the pilot bearing, but now it's not spinning. Has anyone had problems with the bearing? Any advise? How do I get it back out?
|
#69
|
||||
|
||||
$90 for DS and $35 for fw. YMMV. Where are you located? Update bio/sig
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42 |
#70
|
||||
|
||||
How did you determine that the pilot bearing is not spinning? What part of it is not spinning. Remember that the center part only is what spins. Not impossible to determine if it is spinning, but it is too far in the hole to tell with your finger. Unless you abused it something awful, it should turn well, and unless you have hard evidence it is not turning I wouldn't worry about it. Did you have any difficulty getting it all the way in the bore?
__________________
Junqueyardjim Christianity, if false, is of no importance, and if true, of infinite importance. The only thing it cannot be is moderately important. C.S. Lewis 1983 Mercedes W123 240D 4 Speed 285,000 on the road with a 617 turbo, beautiful butter yellow, license plate # 83 240D INDIANA 2003 Jaguar Type X, AWD. beautiful, good mileage, Mom's car, but I won't let her drive it! |
#71
|
|||
|
|||
Yes, it wasn't really going into the bore straight, I used a socket and hammer, and it finally went in, but now the center doesn't spin. How far is it supposed to go into the bore?
|
#72
|
||||
|
||||
I dont know if its possible to drive it in too far. I've never had a problem putting one in. There should be a half round (dome shape) piece with a round hole in the top to make sure the bearing stays in the hole. The tranny input shaft goes through the hole and into the bearing.
__________________
1985 Euro 240D 5 spd 140K 1979 240D 5 spd, 40K on engine rebuild 1994 Dodge/Cummins, 5 spd, 121K 1964 Allice Chalmers D15 tractor 2014 Kubota L3800 tractor 1964 VW bug "Lifes too short to drive a boring car" |
#73
|
|||
|
|||
I installed it, but the inside piece does not spin anymore
|
#74
|
|||
|
|||
You need to be careful when driving in a pilot bearing that the driving socket only contacts the outside of the bearing. If it presses on the inside, it will ruin the bearing. Sounds like that may have happened. To get it out, stuff grease in the hole, then take a dowel or metal rod about the same size as the inside diameter (ID) of the bearing. When you have enough grease in there, put the rod in the ID and tap it with a hammer. The grease will push the bearing out. You may have to add more grease if the rod bottoms out.
As far as flywheel bolt torque goes, look back a few posts on this thread. I posted a copy of the FSM page that tells you all the specs on that. I believe it's 30-40 nM and then an additional 90 degrees. AKA very, very tight. New bolts should be used if the waists are smaller than specified. -Dan
__________________
1976 w115 300D 4-speed conversion!! 1985 w123 300TD 4-speed conversion!! Non-Mercedes old stuff: 1941 Buick Special (Straight 8!) 1946 Luscombe 8a 1947 Willys CJ2a 1950 Chevrolet 4400 dump truck 1954 Chevrolet 3600 3/4 ton 1954 Cessna 195B 1955 John Deere model 40 1991 Ford Taurus SHO 2013 Jetta SportWagen TDI 6-speed (I sold out... |
#75
|
|||
|
|||
Attached is a pic of how deep I pressed the pilot bearing in my last conversion -- to the bottom of the chamfer in the bore.
-Dan
__________________
1976 w115 300D 4-speed conversion!! 1985 w123 300TD 4-speed conversion!! Non-Mercedes old stuff: 1941 Buick Special (Straight 8!) 1946 Luscombe 8a 1947 Willys CJ2a 1950 Chevrolet 4400 dump truck 1954 Chevrolet 3600 3/4 ton 1954 Cessna 195B 1955 John Deere model 40 1991 Ford Taurus SHO 2013 Jetta SportWagen TDI 6-speed (I sold out... |
Bookmarks |
|
|