Been under the weather for a week now and going stir crazy We have also had 90km/hr winds howling by our house along with heavy rain at times.

Wife went out, so despite her instructions to forget about the car until I am better, I went out and finished job (car is in garage)

I had front of car jacked up and temperature switch out of tstat housing. Just filled through overflow tank until a/f gurgled out of switch socket. Screwed temp switch back in. Ran engine for a while. No leaks, no belt noise!
Took car for short drive to get fully up to temperature with heater blasting. Heater worked well, no change in coolant level and no leaks.

Summary: This job started out as - find the mystery noise. That turned out to be alt belt slipping. Changed belts. Noise gone. BUT, noticed AF dripping on belt from tstat housing. Drained rad and changed tstat and seal, but found pitting in casting. JBweld fixed that. Re-installed rad plug, but broke it Bought a couple of spares and finished job today!

Back indoors trying to shake off flu.

PS: I have the FSM but don't have a torque wrench that can measure 1.5-2 Nm!

__________________
Graham
85 300D,72 350SL, 98 E320, Outback 2.5

Just use a coin to tighten the radiator drain plug. That's all you need.

__________________
Marshall Welch
Seattle, WA
1982 300D-T

As for torque setting... I use a 1/4" ratchet and grip only the head. Tighten that way then push a bit on the handle.

__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread
"as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do!

My drivers:
1987 190D 2.5Turbo
1987 560SL convertible
1987 190D 2.5-5SPEED!!!

1987 300TD
2005 Dodge Sprinter 2500 158"WB
1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere!

if that plug is getting hot... there's something wrong with your engine or cooling system... the lower tank should have the coldest coolant. often ambient temp...

__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread
"as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do!

My drivers:
1987 190D 2.5Turbo
1987 560SL convertible
1987 190D 2.5-5SPEED!!!

1987 300TD
2005 Dodge Sprinter 2500 158"WB
1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere!

Nothing wrong with my engine or cooling system that I know of!

For a rad to work, it needs a substantial temperature difference between coolant and incoming ambient air at both inlet and outlet. Temperature drop of coolant across a rad would likely be in the 10-30F range. Say 20F on average. So if hot coolant is at 180F, then bottom of rad would be at about 160F.

160F is still pretty HOT!

Above is theoretical based on some guesses of heat load and coolant flow. It would be interesting to measure actual temperature using an IR gauge.

__________________
Graham
85 300D,72 350SL, 98 E320, Outback 2.5

That's normally true, but the 617 uses a high capacity bypass system. Only a small amount of coolant is sent to the radiator, and the output back to the engine is barely warm. When the system is at full capacity, then the bottom of the radiator would be warmer. On my signature car, I can hold on to the return elbow going back to the t-stat housing on all but the hottest days.

__________________
'83 300D, 126K miles.