|
|
|
#1
|
||||
|
||||
Testing Fuel Pressure
Can anyone offer advice on checking fuel pressure on my '92 201 with 102 engine?
Thanks in advance. Jeff Pierce
__________________
Jeff Pierce Current Vehicles: '92 Mercedes 190E/2.3 (247K miles/my daily driver) '93 Volvo 940 Turbo Wagon (263K miles/a family truckster with spunk) '99 Kawasaki Concours Gravely 8120 Previous Vehicles: '85 Jeep CJ-7 w/ Fisher plow (226K miles)'93 Volvo 940 Turbo Wagon '53 Willys-Overland Pickup '85 Honda 750F Interceptor '93 Nissan Quest '89 Toyota Camry Wagon '89 Dodge Raider '81 Honda CB 750F Super Sport '88 Toyota Celica '95 Toyota Tacoma '74 Honda CB 550F |
#2
|
|||
|
|||
Having the correct adapters & a guage that can read 100PSI is critical..also gas is flammable! Make sure that you have checked for leaks before starting engine.
You need to check "system" pressure..about 82-90psi & control pressure..about 7psi less than system pressure.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#3
|
||||
|
||||
Thanks for the reply, Doc.
I assume system pressure is the pressure supplied by the pump, and control pressure is what's downstream of the regulator? Again, thanks. Jeff Pierce
__________________
Jeff Pierce Current Vehicles: '92 Mercedes 190E/2.3 (247K miles/my daily driver) '93 Volvo 940 Turbo Wagon (263K miles/a family truckster with spunk) '99 Kawasaki Concours Gravely 8120 Previous Vehicles: '85 Jeep CJ-7 w/ Fisher plow (226K miles)'93 Volvo 940 Turbo Wagon '53 Willys-Overland Pickup '85 Honda 750F Interceptor '93 Nissan Quest '89 Toyota Camry Wagon '89 Dodge Raider '81 Honda CB 750F Super Sport '88 Toyota Celica '95 Toyota Tacoma '74 Honda CB 550F Last edited by tvpierce; 09-19-2006 at 07:18 AM. |
#4
|
|||
|
|||
System pressure is measured at the TOP of the fuel distributor..at the fitting that goes to the cold start injector.
The control pressure is measured at the lower section of the fuel distributor..removal of a 12mm plug & installing a fiting is required to check that lower chamber pressure...that pressure is controlled by the EHA EHA= electro-hydraulic actuator.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#5
|
||||
|
||||
Doc,
As always, thanks for sharing your knowledge! Jeff Pierce
__________________
Jeff Pierce Current Vehicles: '92 Mercedes 190E/2.3 (247K miles/my daily driver) '93 Volvo 940 Turbo Wagon (263K miles/a family truckster with spunk) '99 Kawasaki Concours Gravely 8120 Previous Vehicles: '85 Jeep CJ-7 w/ Fisher plow (226K miles)'93 Volvo 940 Turbo Wagon '53 Willys-Overland Pickup '85 Honda 750F Interceptor '93 Nissan Quest '89 Toyota Camry Wagon '89 Dodge Raider '81 Honda CB 750F Super Sport '88 Toyota Celica '95 Toyota Tacoma '74 Honda CB 550F |
Bookmarks |
|
|