|
|
|
#1
|
|||
|
|||
M104 Crank pulley bolt torque
Car: 1995 C280, Engine: M104
I need the torque value for the bolt holding the vibration damper to the crankshaft. I can't find any reference to this for the M104 on my CD (plenty on M111, 112 and 113) and I haven't found it with the search either. |
#2
|
|||
|
|||
124 CD shows 400Nm with dished washers , 370Nm with conical washer...
[295 or 273 ft/lbs..............]
__________________
A Dalton |
#3
|
|||
|
|||
Thank you Arthur.
|
#4
|
|||
|
|||
That is Job 03-3420 on the 124 CD . For 124/202 chassis.
Might be the same on your CD .
__________________
A Dalton |
#5
|
|||
|
|||
Arthur, thank you once again.
The documents on the W202 CD carry the WIS naming convention, so 03-3420 is something like AR03.30-P-1600C (which happens to be the procedure for the M111). I have checked every PDF on the CD and can't find the M104. I am surprised by the 400Nm. My M103 paper manual calls for 300Nm and with the M104 being an evolution of the M103 I thought it would be pretty close. The M111 is also 300Nm. The M112/113 isn't a good reference because they call for a combination of 200Nm followed by 95 degrees of further rotation. Anyway, it shows that assuming something can be dangerous. I am going to have to borrow a torque wrench to do this one. My Snap-On 1/2" drive tops out at 338Nm. |
#6
|
|||
|
|||
Yeah...the 124 CD does specify 104 engine, with the difference being in which version crank washer set-up is used. They also mention lubing the bolt threads and washer/s..
There is quite a bit of difference 103/104.. You want a wrnech that has a 350 Nm as a center range to be accurate.
__________________
A Dalton |
#7
|
|||
|
|||
>>
That is very surprising, as all C280/202 chassis used the 104 HFM/SFI engine...
__________________
A Dalton |
#8
|
|||
|
|||
Arthur - Maybe I should be a bit clearer - I can't find this particular procedure for the M104 on the CD.
But I do agree with you - it is very surprising. STARtekinfo lists is a later version of the CD - P/N P-2700-202-06. Mine is P-2700-202-03. Maybe the later CD has the procedure. |
#9
|
|||
|
|||
< I can't find this particular procedure for the M104 on the CD.
> That is what I was referring to...one would think it would certainly be in the CD for 202 chassis. In the 124 CD , it is Under Engine/Front cover jobs. And also surprisingly, it did in fact mention for 124/202/129 chassis..which I found odd in a 124 CD...but I attribute that to the fact that all those chassis use some form of the 104 engine..[ which is why they mention both washer types]
__________________
A Dalton |
#10
|
|||
|
|||
Arthur - I went through the CD again and there is virtually nothing on the M104. I think that may be because M-B publishes the following two manuals for the M104:
P/N QL-6516-2599-02 Engine M104 S-2599-093 Engine Manual M104 Anyway, I know the procedure and have the tools (flywheel lock, pullers, seal arbor and a borrowed 400 ft/lb torque wrench). It is just the torque value that I was missing and I wasn't comfortable transposing the specs for the other engines to the M104. |
#11
|
||||
|
||||
If you weigh a little under 200, just get an 18" breaker bar and stand on the end
__________________
Prost! |
#12
|
|||
|
|||
If he weighted 200 lbs and wanted 400ft/lbs of torque , he would have to
have a 24" breaker bar... T= Force X Length. [ @ 90 degrees]
__________________
A Dalton |
#13
|
||||
|
||||
Gee, thanks for the Statics 101 refresher. Only the required torque is not quite 300 ft-lbs, per your original post.
__________________
Prost! |
#14
|
|||
|
|||
Quote:
Good One Hirn... Prost to you....
__________________
A Dalton |
Bookmarks |
|
|