Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 11-21-2001, 09:17 PM
Registered User
 
Join Date: Nov 2001
Posts: 126
Arrow Brake System Question

Pertaining to my 1988 190e 2.3 8v without ABS .

I rebuilt my calipers, installed new Brembo discs front and rear, new pads front and rear (oem), new lines, new hoses, and new brake fluid Pentosin Dot 4.

The problem is that I have to use a lot of pressure to stop the car. What can I do to check my system? Also, I'm wondering how I can know if my power brake booster is functioning properly and if master cylinder needs to be rebuilt or not. Another thing that I'm wondering is if there is air in the hydraulic system, could that be thew reason why I'm experiencing this problem.

Thanks in advance.

Reply With Quote
  #2  
Old 11-21-2001, 11:37 PM
Moderator
 
Join Date: Jul 2001
Location: Woolwich, Maine
Posts: 3,598
philipminion,

When you appy the brakes is the pedal "hard" or "soft" and how much travel do you go through?

Air would tend to let you push the pedal further to compress the air, making the feel more on the soft or spongy side.

It is also possible the new discs came with a preservative that is interfering with your pad/disc ability to convert kinetic energy to heat, and until it wears off you will have a less effective braking system. I think you are supposed to clean them (the discs) off when you install them.

If you get the chance, call the outfit that sold the discs to you and ask them if they ship with a preservative. Since most discs are made of non-corrosion resistant steels, it is not uncommon to coat them with something to prevent them from degrading in storage or shipping. Like wet brakes, until the material is removed, it acts like a lubricant, making your foot push harder to get an acceptable response.

If you cannot "burn" the stuff off by driving around with the brake applied lightly, you will probably have to take the calipers off to wash the stuff off so you do not contaminate the pads.

Based on what you wrote that is about the best I can do, hope it helps, and good luck. Jim
__________________
Own:
1986 Euro 190E 2.3-16 (291,000 miles),
1998 E300D TurboDiesel, 231,000 miles -purchased with 45,000,
1988 300E 5-speed 252,000 miles,
1983 240D 4-speed, purchased w/136,000, now with 222,000 miles.
2009 ML320CDI Bluetec, 89,000 miles

Owned:
1971 220D (250,000 miles plus, sold to father-in-law),
1975 240D (245,000 miles - died of body rot),
1991 350SD (176,560 miles, weakest Benz I have owned),
1999 C230 Sport (45,400 miles),
1982 240D (321,000 miles, put to sleep)
Reply With Quote
  #3  
Old 11-22-2001, 06:17 AM
Mike Stone
Guest
 
Posts: n/a
New Brake Discs

Sorry to say, but if you had preservative on the rotors it will have ruined your pads.

Had it myself quite a few years ago.

After I was advised to clean the rotors off I reused the same pads and ended up cleaning the rotors a second time and fitting new pads.

By the way the best thing to clean them off is paraffin (kerosene) as it is VERY slightly abrasive. It will really get into the machining marks.
Then give a final clean using petrol to get rid of any residuals.

Don't forget the edges and the hub.

Mike Stone

Reply With Quote
  #4  
Old 11-22-2001, 09:20 AM
Registered User
 
Join Date: Nov 2001
Posts: 126
JimSmith

Thanks Jim

When I apply the brakes the pedal feels hard and requires some strength to stop the car. I'm actually going to go out for a road test again and think about how the pedal feels to be sure. After reading your post, I feel like I'm not sure. I'll confirm and repost.

The discs were cleaned prior to installation, because they did have that preservative that your talking about and it was also mentioned on the instruction sheet that came with them.
Reply With Quote
  #5  
Old 11-22-2001, 09:23 AM
Registered User
 
Join Date: Nov 2001
Posts: 126
Mike Stone

The discs were cleaned prior to installation, because they did have that preservative that your talking about and it was also mentioned on the instruction sheet that came with them.So I did clean them thoroughly before I installed them.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wrong fluids in the brake system. ericnguyen Tech Help 17 04-01-2005 07:31 PM
Dumb question: Just how do you flush an AC system? (83 240D) Carrameow Tech Help 1 09-16-2003 10:50 AM
500 SL (R129) Brake Question jgl1 Tech Help 2 11-15-2001 12:39 PM
Brake system noise question dennis1522 Tech Help 1 06-13-2000 08:18 PM



All times are GMT -4. The time now is 05:44 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page