I was able to slide under the car a little bit and take some pictures of the front disk. Does anything look out of order with the front disk? Should those bolts be seated that way?

Attached Thumbnails

       

__________________
1993 Benz-190E-2.6 liter

From what I know those mounting bolts have all shifted quite abit.
Wear, misalignment or just plain bad all could cause that.

__________________
1985 300D 198K sold
1982 300D 202K
1989 300E 125K
1992 940T

"If you dont have time to do it safely, you dont have time to do it"

"The democracy will cease to exist when you take away from those who are willing to work and give to those who would not."

Thanks bob I was hoping the front disc would not be the problem but if I can be sure that is the problem I would feel better knowing for sure.

Do you think that front disc could be causing the symptoms that I mentioned? Did you see any problem with the pictures I posted of the rear disc area?

__________________
1993 Benz-190E-2.6 liter

Definitely needs attention as there are gaps which allows for slack upon movement (hence why you only notice it while moving).

Not entirely sure that is the whole problem, but it sure would be contributing. Common wear item every 60-80k, so just change it out for both good measure and preventative maintenance. Don't want that baby to crack in two while you are on the freeway!

__________________
2016 Monsoon Gray Audi Allroad - 21k
2008 Black Mercedes E350 4Matic Sport - 131k
2014 Jeep Wranger Unlimited Sahara - 62k
2003 Gray Mercedes ML350 - 122k

The clunk in the rear of the car is probably the differential mounts. I have that in my 87 300e.

__________________
Eugene

10 E63 AMG
93 300te 4matic
07 BMW X3
14 Ford F-150 Fx2

There would have to be a hell of a lot of slop in a flex disc or an axle to cause a noticeable hesitation. Even 5-10 degrees of slop, which would be rather a lot for a flex disc or axle would barely be noticeable as a hesitation, but it would certainly be likely to clunk.

I think you have more than one issue here. Sounds to me like the transmission is engaging late, and when it does the sudden torque increase causes the slop in the flex discs and/or rear axle(s) to clunk audibly.

That rear differential looks pretty oily, you may want to check that the fluid level is adequate too.

Check the trans fluid level. Low fluid can cause all sorts of weird trans symptoms including slipping, late shifts, etc...... A clogged trans filter could also be to blame.

__________________
-tp


1990 300SE "Corinne"- 145k daily driver - street modified differential - PARTING OUT OR SELLING SOON - PORTLAND OR. AREA - PM ME FOR DETAILS
1988 560SEL "Gunther"- 190K passes anything except a gas station
1997 S420 - 265k just bought it with a rebuilt trans. Lovely condition

Thanks for all the replies. I checked his tranny fluid level. That seems fine.

I dont know how to check the differential level. Can anyone explain that for me?

Mechanic wants $400 to do the front disc if that is the problem

__________________
1993 Benz-190E-2.6 liter

It is noticeable when stepping on the gas from a stop. Once the car gets moving it is not noticeable.

Is it a hard DIY procedure for us to do at home in the garage?

__________________
1993 Benz-190E-2.6 liter

Not too terribly hard if you have proper equipment.


CAUTION - When you disconnect the drive shaft, there is no longer a park pawl holding the car in place. The car must be on a level surface and carefully chocked!


How much of a hesitation are we talking about here, anyway?

__________________
-tp


1990 300SE "Corinne"- 145k daily driver - street modified differential - PARTING OUT OR SELLING SOON - PORTLAND OR. AREA - PM ME FOR DETAILS
1988 560SEL "Gunther"- 190K passes anything except a gas station
1997 S420 - 265k just bought it with a rebuilt trans. Lovely condition

I'm still not convinced the problem is not in the trans. You say the problem happens every time you start from a dead stop. Well, let's use our imaginations for a second..... Any slop in the drive train will get taken up when you shift from park or neutral into drive, right? The torque from the trans is supposed to always be present on the drive train when the car is in gear. This is why the car starts to move by itself when you take your foot off the brake. So, that slop goes away the very first time you go into gear, right? Okay, so how then does it re-appear at every stoplight unless the driver is shifting to neutral?

The only way this could be happening is if the trans is not applying torque to the drive train at all times, and that points to trans problems.

__________________
-tp


1990 300SE "Corinne"- 145k daily driver - street modified differential - PARTING OUT OR SELLING SOON - PORTLAND OR. AREA - PM ME FOR DETAILS
1988 560SEL "Gunther"- 190K passes anything except a gas station
1997 S420 - 265k just bought it with a rebuilt trans. Lovely condition

It's easy to replace. When I replaced my front flex disc, I had to remove the rear one so I could slide the drive shaft back to remove and install the front one.

__________________

1993 190E 2.3
2001 SLK230
1971 LS5 (454) Corvette Convertible

Not a tremendous amount. I did not notice it at first.

I also have not noticed it in reverse yet.

__________________
1993 Benz-190E-2.6 liter

Is it basically removing 6 bolts from the rear and removing 6 bolts from the front and just pulling it out? Are there any other parts like the bearing I should check out while it is of?

__________________
1993 Benz-190E-2.6 liter

Yes, that's about it. One thing I like to do is put witness marks on the shaft/connectors so that the drive shaft goes back on the the same position.

__________________

1993 190E 2.3
2001 SLK230
1971 LS5 (454) Corvette Convertible

Remove filler plug at differential, stick your finger in the hole, if low, add fluid, screw filler plug back in.

__________________

1993 190E 2.3
2001 SLK230
1971 LS5 (454) Corvette Convertible