Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-09-2003, 07:33 AM
Registered User
 
Join Date: Jan 2003
Location: USA
Posts: 699
Electrical quiz for my MB friends.

Dear friends:

1) If you take a look at multimeters, you will notice that most of them only support a maximum of 1mA to 10A for DC, and 1A to 1000A for AC, even though they support voltage range of 1V to 1000V for both DC and AC. The question is: If multimeters can only handle low current (A) loads for DC, why it can handle much larger loads for AC ?

Diesel afficionados have always wanted a multimeter that can handle at least 30 A for DC so that they can efficiently test their glow plugs easily (measuring resistance only is not deterministic of a actual condition of a glow plug). Unfortunately, such multimeters are very expensive (high end Flukes...)


2) What are the proper terms to describe the opposition to a DC current and an AC current? Do they use the same unit?

Good Luck :-)


Eric

Reply With Quote
  #2  
Old 07-09-2003, 07:57 AM
LarryBible
Guest
 
Posts: n/a
I think you're comparing oranges to apples. The same meter that measures 10A DC will not measure 1000A AC. Current is a series measurement. 1000A AC would fry most anything that does not have a cable that is less than a half inch in diameter.

For measuring higher currents you simply use a high wattage, low tolerance, 1 Ohm resistor wired in series with the load. You then take a voltage measurement across the resistor and using Ohms law determine the current through the resistor. Inside the DMM, that's what they are doing, it's just that they can't fit a very high wattage resistor into the case and provide large enough wires to handle the current.

Have a great day,
Reply With Quote
  #3  
Old 07-09-2003, 08:26 AM
Gilly's Avatar
Registered User
 
Join Date: Mar 2001
Location: Evansville WI
Posts: 9,616
Just to bypass the whole technical "thing" (thanks Larry), I have a 0-60 analog ammeter (it's old, it's a Mac ET 1008, made by Prime Instruments in Cleveland, OH. Bought it in the early 80's.

I tried checking around a little, couldn't come up with anything comparable on the net, but I'm sure they're out there somewhere.

Gilly
Reply With Quote
  #4  
Old 07-09-2003, 09:03 AM
Registered User
 
Join Date: Sep 2002
Location: Newcastle upon Tyne, UK
Posts: 215
Quote:
What are the proper terms to describe the opposition to a DC current and an AC current? Do they use the same unit?
DC is resistance and is measured in Ohms.

AC is not quite so simple, but you probably are thinking about inductance which is measured in Henrys. Inductance occurs in coils. Straight forward resistance is relevant to AC, too.
__________________
Cheers, Neil
Reply With Quote
  #5  
Old 07-09-2003, 09:16 AM
Registered User
 
Join Date: Dec 2002
Location: Suburban NYC
Posts: 57
Measurement of voitage and resistance is different for AC and DC. AC voltage is measured as rms because of the sinusoidal nature of the waveform. Look on a scope; the trace crosses above and below the zero line.. DC is measured in straight volts. DC appears as a straight line on a scope.
In AC work, resistance is sometimes expressed as impedance; i.e. in measuring the “resistance” of a speaker coil, also expressed in ohms (usually 4, 8 or 16 ohms.)
__________________
Stage Wizards Lighting and sound designer
1981 SD 328,000
1985 300TD, 266,000
1984 300 TD, 267,000
Reply With Quote
  #6  
Old 07-09-2003, 11:09 AM
Registered User
 
Join Date: Feb 2002
Location: St. Louis, MO
Posts: 340
Resistance to AC Current Flow

This "resistance" to AC current flow is called impedance and can be capacitive or inductive or purely resistive in nature. Think of impedance as being the long side (hypotenuse) of a right triangle with the resistance as the base and the capacitive or inductive component at a right angle to it. The magnitude if the capacitive component is inversely proportional to the frequency of the voltage while the magnitude of the inductive component is proportional to it.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 12:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page