|
|
|
|
|
#1
03-02-2011, 11:23 AM
|
||||
|
||||
|
Anyone have a 123 trailing arm handy? Need specs
Needs specs on the bearing/bushing holes where it attaches to the subframe. Diameter and length please. Think I found a camber kit that might work for adjusting toe and camber.
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42 
|
|
#2
03-02-2011, 11:57 AM
|
|||
|
|||
|
Yes, I use one as a door stop here in the living room...
and another as a paper weight in my office... eliminates the need for weight training.... LOL
__________________
1980 240d , chain elongation, cam marks reference: http://www.peachparts.com/shopforum/showthread.php?threadid=10414 http://www.peachparts.com/shopforum/diesel-discussion/305365-9-degrees-chain-stretch.html evap fin cleaning: http://www.peachparts.com/shopforum/showthread.php?t=156207&highlight=evaporator A/C thread http://www.peachparts.com/shopforum/diesel-discussion/297462-c-recommendations-mb-vehicles.html
|
|
#3
03-02-2011, 12:48 PM
|
||||
|
||||
|
Ottoman in front of my chair...
__________________
CC: NSA All things are burning, know this and be released. 82 Benz 240 D, Kuan Yin 12 Ford Escape 4wd You're four times It's hard to more likely to concentrate on have an accident two things when you're on at the same time. a cell phone. www.kiva.org It's not like there's anything wrong with feeling good, is there?
|
|
#4
03-02-2011, 12:55 PM
|
||||
|
||||
|
I'll measure some bits for you tomorrow
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior  Don't leave that there - I'll take it to bits!
|
|
#5
03-03-2011, 09:43 AM
|
||||
|
||||
|
Measurements made on a pre 1981 steel W123 trailing arm:-
Diameter of the hole for the bushing => 41.95mm Length of "tube bit" that holds the bushings => 47.91mm (Most consistent measurements reported!)
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits!
|
|
#6
03-03-2011, 09:44 AM
|
||||
|
||||
|
Thanks.
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42
|
|
#7
03-16-2011, 04:21 AM
|
||||
|
||||
|
Quote:
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits!
|
|
#8
03-16-2011, 10:46 AM
|
||||
|
||||
|
Quote:
I am betting something like this would work in the trailing arm bushings on the w123 and should adjust toe in and caster to some degree.
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42
|
 |
| Bookmarks |
|
|
Linear Mode
