|
|
|
|
|
#1
03-25-2007, 03:18 AM
|
|||
|
|||
|
94 S600 Will not start ?
Car will turn over but will not start. I pulled a plug wire off ...no spark. I do have fuel pressure, just will not start???? Any help is greatly appreciated gang!
P.S. Have a GOOD battery as well. Thanks ! 
|
|
#2
03-25-2007, 03:54 AM
|
||||
|
||||
|
I'm afraid it's the EZL module. But not 100% sure.
__________________
Master Computer Engineer, A+, Network+, MCP/MCSA/MCSE 4/2k/2k3 - Messaging, MCTS, MCITP, MCT, Brainbench, ICDL and starting Ph.D 380SE 1984 <------- Totaled by flipping accident 300SE 1988 <------- Sold Volvo S70 2000 <---- 4 family Opel Omega 2002 <-- 4 family 560SEC 1989 <------ Sold 560SEL 1990 <------ Sold 560SEL 1991 <------ 4 my mother 560SEL 1989 <------ Sold 600SEL 1992 <------ Current
|
|
#4
03-25-2007, 09:43 AM
|
|||
|
|||
|
Did you try locking and unlocking the doors from the outside?
__________________
Chuck Taylor Falls Church VA '66 200, '66 230SL, '96 SL500. Sold: '81 380SL, '86 300E, '72 250C, '95 C220, 3 '84 280SL's '90 420SEL, '72 280SE, '73 280C, '78 280SE, '70 280SL, '77 450SL, '85 380SL, '87 560SL, '85 380SL, '72 350SL, '96 S500 Coupe
|
|
#5
03-25-2007, 10:02 AM
|
||||
|
||||
|
Modules are $$$....can't really test it unless you happen to have a known good spare sitting around.
I do send them off for testing from time to time...But these cars are known for eating their modules (Mercedes decided to not fuse them for some daft reason) . I can't remember if by 94 you still had 2 or if they had consolidated to 1 EZL. Jonathan
__________________
Blue Ridge Mercedes Jonathan Hodgman http://www.blueridgemb.com/ Enthusiast Service, Restoration & Tuning. Follow Us on Facebook! Located in the Atlanta area Specializing in all pre and post merger AMG's including Hammers and DOHC M117 engines. Mercedes Repair Atlanta
|
|
#6
03-25-2007, 04:39 PM
|
|||
|
|||
|
I did not hear crank position sensor ? a visit or tow to MB to read codes before throwing parts into it
|
|
#7
03-27-2007, 12:07 AM
|
|||
|
|||
|
Thanks
O yea, i failed to mention, the car sat for roughly a month. I only cranked twice. No problems. Cranked right away. About a week later, I cranked it again it started right up......for about a second then just would turn over but not crank. I pulled a plug wire off and did not see any "zap".
 . I hope this will help you guru's out there bring BIG BERTHA back to life.Thanks, cibrspeed
|
|
#8
03-27-2007, 06:23 AM
|
|||
|
|||
|
<
Huh ?? Crank is a common term for the engagement of the starter motor, which is also called turn over. so, what do you mean ?? Crank is a carry down term that comes from the old cars that actually had a hand crank at the front of the engine. Electric starter motors eliminated hand cranking, but the term Crank still refers to the spinning of the engine in order to get it to Start/Run..
|
|
#10
03-27-2007, 05:23 PM
|
|||
|
|||
|
..then my first suspect would be the Crank Position sensor..that triggers the ignition module.
Do a search for it [ also called reference sensor]
|
 |
| Bookmarks |
|
|
update
Linear Mode
