|
|
|
#1
|
||||
|
||||
Working on brakes: how difficult?
I started as a newbie DIYer over the past several days: engine oil change, transmission/differential fluid changes were made easy thanks to your precious advice here...
I now need to inspect my breaks and possibly replace some pads and do whatever adjustments are required: how difficult is all that for a beginner such as myself? Is it enough for me to rely on the Haynes W123 book or do I need more? I would much appreciate any pointers you can give me, mentions of special tools that are required, useful warnings, etc. Thanks Rino
__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior. |
#2
|
||||
|
||||
I dont know what breaks are but brakes are pretty straight forward on any car. Just remember the fluid reservoir has a wall in it seperating the from from the back (to prevent total fluid loss if the front or back lines busted).
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42 |
#3
|
||||
|
||||
I try not to work when on break.
But they're not bad at all. Replacing pads is easy, I'd do the hoses while you're in there too. Flush the system too. Also check the rest of the system out for issues... rotor thickness, e-brake functionality, etc.
__________________
I'm not a doctor, but I'll have a look. '85 300SD 245k '87 300SDL 251k '90 300SEL 326k Six others from BMW, GM, and Ford. Liberty will not descend to a people; a people must raise themselves to liberty.[/IMG] |
#4
|
|||
|
|||
The brake pads for example are an extremely easy design to change on mercedes. So go for it. If at any time you feel uncomforatable with any procedure just ask for help on the site. That is one of the primary functions of this site. The flipside is you will be able to help others yourself down the road. Your manual is quite helpful in it's brake section as well. .
Try not to ask questions about engine oils though. Instead just search the archives. There is nothing like an oil question to get the feathers flying around here. It almost becomes irrational at times in fact. |
#5
|
||||
|
||||
Brakes are not a hard deal at all if you see it done. I just came out with the Front brakes DVD that shows you how to do the job right.
You can do it.
__________________
1981 300D 147k 1998 VW Jetta Tdi 320k 2001 Dodge Ram 2500 141k 1979 300D 234k (sold) 1984 300D "Astor" 262k(sold) Mercedes How-To and Repair Pictorials I love the smell of diesel smoke in my hair |
#6
|
||||
|
||||
Thank you guys for your advice. I am a beginner and find the thing a bit confusing... Bleeding the brake system for instance... Do I buy a power bleeder, do I use the traditional method (a second person pumping on the brake pedal), do I make my own device? These are the types of puzzling choices I was referring to. I've never done it, so I have no idea how difficult and would appreciate some practical pointers. Can I do the work jacking up one wheel at a time? I don't have standing jacks and there's really no extra space I can use in my apartment or common-area garage for that type of thing... Is it something that requires a lot of extra special tools? In which case I'd probably be better off taking the car to someone to perform the job for me. Oil change, transmission/differential fluid change were easy... but brake maintenance... I need to find out if it is something within my reach and something I can do without spending a fortune on specialized tools... it is on these points that I'd much appreciate your opinions and suggestions...
Thanks, Rino
__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior. |
#7
|
||||
|
||||
Quote:
Hey, I know what breaks are, but what the heck is from from.....
__________________
Jimmy L. '05 Acura TL 6MT 2001 ML430 My Spare Gone: '95 E300 188K "Batmobile" Texas Unfriendly Black '85 300TD 235K "The Wagon" Texas Friendly White '80 240D 154K "China" Scar engine installed '81 300TD 240K "Smash" '80 240D 230K "The Squash" '81 240D 293K"Scar" Rear ended harder than Elton John |
#8
|
||||
|
||||
Haven't done brakes on the Mercedes yet, but have on other cars. Its really useful to use jackstands to take both front or back wheels off at the same time (you don't want to work under a car on a jack anyway), that way you can bring both rotors to be turned at the same time. You can get small jackstands for passenger cars for around $40/pair, and they don't take up much room when stored. Throw in a flat piece of wood and you've got yourself a coffee table!
Disk brakes are pretty easy, but you may need a c-clamp or something to push the caliper piston back into the caliper, since your new pads will be thicker than the old ones, you'll need the extra room. If you've got a second person handy, have them pump up the brake pedal while you bleed...I like that better than the one-man bleeders anyway, but that's just my preference. Good luck.
__________________
1985 300TD-euro 352,000 mi 1974 240D (1?)52,000 mi - has a new home now |
#9
|
||||
|
||||
Since you've successfully accomplished the other tasks you should have no problem with the brakes.
You need to buy some jackstands as you will have to remove the wheel. Knock the two pins out of the caliper, remove the retaining clip and slide out the old pads. Push the piston back, insert new pads, retaining clip and pins and you are done. Do it yourself, save the money and take pride in working on your own car. Good luck. Scott
__________________
Scott 1982 Mercedes 240D, 4 speed, 275,000 1988 Porsche 944 Turbo S (70,000) 1987 Porsche 911 Coupe 109,000 (sold) 1998 Mercedes E300 TurboDiesel 147,000 (sold) 1985 Mercedes 300D 227,000 (totaled by inattentive driver with no insurance!) 1997 Mercedes E300 Diesel 236,000 (sold) 1995 Ducati 900SS (sold) 1987 VW Jetta GLI 157,000 (sold) 1986 Camaro 125,000 (sold - P.O.S.) 1977 Corvette L82 125,000 (sold) 1965 Pontiac GTO 15,000 restored (sold) |
#10
|
||||
|
||||
Refering to brake bleeding, two person method works fine. Down side, it takes two people...Okay, pads straightforward. Channel locks to push calipers back, ONE AT A TIME!!! Keep one pad on to hold other. Tools needle nose pliers to remove sensors and cotter pins. Punch to drive pins out. Hammer, ball pein. Pull retaining springs. 19mm socket, not normally in set.
__________________
83 SD 84 CD |
#11
|
||||
|
||||
I also recommend jackstands... that said, a large block of wood under the frame of the car with the car on a jack is kinda ok... for 50.00 you can get a set of jackstands with a nice 2.5ton floor jack at most auto parts stores, or sears.
as far as bleeding goes, theese cars are so simple. with the cap off the MC suck out the nasty fluid, and fill it with clean fluid, then starting at the back passangers side, open the bleeder screw, it's either 8mm or 10mm, I don't rember... anyway, the system will trickle out gunky fluid, when the gunky stuff stops and you get clear, close her up and move to the closer to the drivers front. RR, LR, RF, then Drivers front. keep filling the resivoir. it is faster with a power bleeder, but not needed on the older MB's. if you want to just change the brakes, it's also simple. just pull the clips, on bendix calipers, or simply drive out the pins on atx calipers. and pull out the pads. reverse to install. some put stickey goo to keep the squeel down. some use a sticky spacer. ymmv John
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread "as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do! My drivers: 1987 190D 2.5Turbo 1987 190D 2.5Turbo 1987 190D 2.5-5SPEED!!! 1987 300TD 1987 300TD 1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere! |
#12
|
||||
|
||||
There are actually more downsides to the two person method. It requires that the bleeder valve be frequently opened and closed. This causes wear on it and also opens the sytem to possibilities of air getting sucked back in.
Just find a jar and appropriate sized hose. Fill the jar with some clean fluid and make sure one end of the hose is in the fluid. Attach the other end to the bleeder. Lift said jar above the bleeder (so the air flows up) get in the car and start pumping on the brakes. Keep an eye on the fluid level (remeber the rear reservoir) and try to keep an eye on the jar. I prefer to pump until its a nice clear color. Get out close the bleeder and move on. No reason to spend even $5 on a 99 cent solution.
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42 |
#13
|
||||
|
||||
Thanks for your advice... I'll get the jackstands at Sears this weekend (any specific suggestable model I should be on the look for? Preferably economical, reliable, and SMALL, so that I can hide them somewhere after use...) and I will look into all you have suggested, with the help of my Haynes manual to make sure I understand everything correctly, and then report back here soon.
While I am at Sears, what are the other special tools I am going to need that I should get there (I have no tools that are specific to brake work). Winmutt, I am unclear about your 99_cent solution: does the jar you mentioned imply the use of a power bleeder along with it, or can I just use the jar and do the bleeding myself without the aid of a second person? Thanks... Rino
__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior. |
#14
|
|||
|
|||
What is this actually called? |
#15
|
|||
|
|||
No Bleeding
Replaced the brake pads a zillion times and never blead the calipers. Only if a hose is replaced.
__________________
1984 300SD turbo 126 "My true love" God made me an atheist and who am I to question His wisdom |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|